background image

FEMA ELECTRÓNICA . Series S . S40-P

18

Protocol  

 

ASCII

Bus type  

 

RS-485, up to 57.6 Kbps

Isolation  

 

1000 Vdc

Slots allowed 

 

‘Opt.1’, ‘Opt.2’

2.5 Module RTU

The S4 module provides a RS-485 communications module for Series 

S of panel meters. ASCII protocol with ‘Master’ / ‘Slave’ architecture. 

Addressable with up to 31 modules. Frames codified in represent

-

able ASCII characters (codes 32 to 255), directly visible using ‘hyper

-

terminal’ or similar programs.

•  Configurable  for  direct  retransmission  to  remote  meters  M60-

485 (14 mm digit height) and BDF Series (60 mm and 100 mm digit 

height).
• Access to display values, alarm status, memory of maximum and 

minimum, alarm setpoints, ...
Configuration from instrument front keypad, through menu entries 

‘Opt.1’ or ‘Opt.2’, depending on the position the module is installed.
The S4 module can be ordered pre-installed into a Series S panel me

-

ter, or standalone for delayed installation, as it does not require sol

-

dering or special configuration.

Terminal B 

B signal from RS-485 bus

 

Terminal A 

A signal from RS-485 bus

Terminal G 

GND

For  more  information  : 

http://fema.es/docs/4254_SERIES_M-K-S_

OPTIONS_manual_i.pdf

Protocol  

 

Modbus RTU

Functions implemented  4 (Read_Input_Registers)
Bus type  

 

RS-485, up to 57.6 Kbps

Isolation  

 

1000 Vdc

Slots allowed 

 

‘Opt.1’, ‘Opt.2’

The RTU module provides a Modbus RTU communications module 

for Series S of panel meters. The RTU module implements function 

‘4’ (‘Read Input Registers’) of the Modbus RTU protocol, to access the 

instrument registers (reading value, alarm status, memory of maxi

-

mum and minimum, ...)
Configuration from instrument front keypad, through menu entries 

‘Opt.1’ or ‘Opt.2’, depending on the position the module is installed.
The RTU module can be ordered pre-installed into a Series S panel 

meter, or standalone for delayed installation, as it does not require 

soldering or special configuration.

Terminal B 

B signal from RS-485 bus

 

Terminal A 

A signal from RS-485 bus

Terminal G 

GND

For  more  information  : 

http://fema.es/docs/4254_SERIES_M-K-S_

OPTIONS_manual_i.pdf

Opt.2

Opt.1

Power

Signal

B  A  G

B  A  G

Opt.2

Opt.1

Power

Signal

B  A  G

B  A  G

2.6 Module S4

Summary of Contents for S40-P





















Reviews: