background image

FEMA ELECTRÓNICA . Series S . S40-P

6

Decimal point

1.10 Configuration menu

Press ‘SQ’ (

<

) for 1 second to access the ‘

configuration menu’. 

For a description on how to operate inside the menus see sec

-

tion 

1.8

. For a full vision of the ‘

configuration menu

’ structure 

see section 

1.11.

Scaling

Input low

Display low

Input high

Display high

To configure the initial set up of the instrument, select the input sig

-

nal range, the decimal point position, and scale the reading.
Access the ‘

Input

’ (‘

InP

’) menu to select the input signal range. Op

-

tions available are 4/20

mA, 0/10

Vdc, ±20

mA y ±10

Vdc. Select the 

rear jumper at position ‘4’ for Vdc or ‘5’ for mA 

(see section 1.5).

Access the ‘

Decimal point

’ (‘

dP

’) menu to select the decimal point 

position. Move the decimal point by pressing the ‘LE’ (

3

) key.

Scale the reading at the ‘

Scaling

’ (‘

ScAL

’) menu. There are four pa

-

rameters to configure :

• ‘

Input low

’ (‘

ILo

’) 

- minimum input signal, in mA or Vdc with 

two decimals.

• ‘

Display low

’ (‘

dLo

’)  - reading associated to the minimum input 

signal.
• ‘

Input high

’ (‘

IhI

’) 

- maximum input signal, in mA or Vdc with 

two decimals..

• ‘

Display high

’ (‘

dhI

’)  - reading associated to the maximum input 

signal.

The ‘

Field correction

’ (‘

F.cor

’) functions allows to correct the instru

-

ment scaling parameters, when the instrument is being installed on 

the field, providing a fast and easy way to compensate offset signals.
To operate the ‘

Field correction

’ (‘

F.cor

’) function for the offset cor

-

rection,  generate  the  minimum  input  signal  and  access  the  ‘

Field 

low

’ (‘

F.Lo

’) function. Then the following sequence will start

 

• message with signal type (‘

mA

’ or ‘

Vdc

’)

 

 

• message ‘

wait

’ (‘

WAIt

’) in flash mode

 

 

• after 5 seconds, message ‘

ok

’ (‘

oK

’) appears

 

 

• at this point, press key SQ (‘

<

‘)

 

 

• the menu returns to menu entry ‘

Field Low

’ (‘

F.Lo

’)

The instrument has read the input signal and automatically config

-

ures the ‘

Input low

’ (‘

I.Lo

’) for you.

Repeat the process generating the maximum input signal and access 

the ‘

Field high

’ (‘

F.hI

’) menu. The instrument will read the input sig

-

nal and automatically configure the ‘

Input high

’ (‘

I.hI

’) parameter to 

match the signal read.

Application - a 0/10 Bar pressure transmitter provides a 4/20 mA out-

put signal. At installation, the operator detects that the reading at 

0 Bar is 0.34 Bar and that at 10 Bar the reading is 10.72 Bar. Apply the 

Field correction

’ / ‘

F.Lo

’ function while reading is 0.34 Bar and the 

instrument will automatically correct the reading to 0.00 Bar. After-

wards, apply the ‘

Field correction

’ / ‘

F.Hi

’ function while reading is 

10.72 Bar and the instrument will automatically correct the reading 

to 10.00 Bar. 

1.10.1 

Initial set-up

1.10.2 

Field correction

Range de 4/20 mA

Range de 0/10 Vdc

Range de ±20 mA

Range de ±10 Vdc

Input

Field correction

Correction high

Correction low

Wait (5 sec.)

 (

<

Wait (5 sec.)

 (

<

Summary of Contents for S40-P





















Reviews: