background image

FEMA ELECTRÓNICA . Series S . S40-P

16

2. Output and control modules

2.1 Module R1

The T1 module provides 1 transistor output to install at digital panel 

meters from Series S, up to a maximum of 2 transistors in a single 

meter. 

Configuration is performed from the frontal keypad of the meter, by 

setting the parameters at the alarm menu. Check the parameters of 

at the alarm menu for full information.
Transistor output is optoisolated, provides 2 terminals for connec

-

tion, and can switch up to 35 V and 50 m

A.

Modules T1 can be ordered pre-installed into a Series S digital panel 

meter, or standalone for delayed installation, as they do not require 

soldering or special configuration.

For  more  information  : 

http://fema.es/docs/4254_SERIES_M-K-S_

OPTIONS_manual_i.pdf

Type of output   

transistor

Max. voltage 

 

35 Vdc

Max. current 

 

50 mA

Isolation  

 

3500 Veff

Type of terminal   

plug-in screw terminal, pitch 5.08 mm

Slots allowed 

 

‘Opt.1’, ‘Opt.2’

‘B’

‘A’

Schematic for T1 output

Opt.2

Opt.1

Power

Signal

A  B  C

A  B  C

The R1 module provides 1 relay output to to install at digital panel 

meters from Series S, up to a maximum of 2 relays in a single meter. 

Note : for more than 2 relays per instrument or larger relay density 

per module, see special modules R2 and R4.

Configuration is performed from the frontal keypad of the meter, by 

setting the parameters at the alarm menu. Check the parameters of 

at the alarm menu for full information.
Relay  with  3  contacts  (common,  normally  open,  normally  closed) 

with up to 250 Vac switching voltage and 8 

A.

Modules R1 can be ordered pre-installed into a Series S digital panel 

meter, or standalone for delayed installation, as they do not require 

soldering or special configuration.

For  more  information  : 

http://fema.es/docs/4254_SERIES_M-K-S_

OPTIONS_manual_i.pdf

Type of relay 

 

3 contact relay (NC, NO, common)

Current maximum 

8 A per relay (resistive load)

Voltage maximum* 

250 Vac continuous

Isolation  

 

3500 Veff

Type of terminal   

plug-in screw terminal, pitch 5.08 mm

Slots allowed 

 

‘Opt.1’, ‘Opt.2’

Terminal A 

Common

Terminal B 

NO - Normally open

Terminal C 

NC - Normally closed

Opt.2

Opt.1

Power

Signal

A  B  C

A  B  C

2.2 Module T1

Summary of Contents for S40-P





















Reviews: