Felton TATE Installation Manual Download Page 21

21

TATE DIGITAL WALL MOUNTED MIXER INSTALLATION GUIDE

WARRANTY

For technical assistance please ring: 0800 743 358 or (09) 528 0810

8 Farmhouse Lane, St Johns, Auckland 1072 New Zealand

Felton Industries Limited

www.felton.co.nz

5 year warranty applies to all 

Felton 

branded products including the electronic hardware and its components. 

Where products are promoted as having a “5 year warranty”, Felton Industries Limited guarantees the electronic 

components of these products (excluding batteries) to be free from defects in materials and workmanship under 

normal installation, use and service for a period of five (5) years from the date of purchase. Fair wear and tear is 

expressly excluded. 

This warranty is effective for five (5) years from the date of purchase and covers electronic replacement parts 

only (excluding batteries) and 2 years from the date of purchase for plumber’s labour relating solely to repairing 

or replacing the Hardware, provided the product is installed by a registered plumber. You must retain proof of 

purchase of the Hardware (such as an invoice or receipt) and proof of installation by a registered plumber and 
provide these to Felton on request.

This warranty is for manufacturing defects only and does not cover any damage to product due to abuse, 

negligence or improper installation. This warranty is given on the understanding that the product is installed 
by a registered plumber and operated according to Felton’s installation guide and the Australian/New Zealand 

standard AS/NZS3500. This warranty is provided to persons who are a “consumer” under the Consumer 

Guarantees Act 1993 only and for use in domestic/residential dwellings only (not for commercial use).

This warranty is subject to any other rights or remedies that you may have under the Consumer Guarantees 

Act 1993 (or any other applicable legislation) and to Felton’s Terms of Trade.

This 

5 year warranty

 does not cover:

 

1) 

any consumable items (e.g. batteries, filters, installation fittings) supplied with the products.

2) 

damage, problems or unsatisfactory performance caused to the electronic hardware by:

 

a. 

Faulty or incorrect electrical wiring, incorrect power supply, voltage fluctuations, over voltage  

 

 

 

transient spikes or electromagnetic interference not originating within the electronic hardware.

 

b. 

Incorrect or poor installation or application

 

c. 

Operation at conditions outside the operating conditions specified in the Felton technical  

 

 

 

                or sales data applicable to that electronic hardware.

 

d. 

Reconfiguration of the digital interface by the user – this is considered a service not a warranty.

MAINTENANCE & CARE

Please see User Guide or visit www.felton.co.nz

Summary of Contents for TATE

























Reviews: