Felton TATE Installation Manual Download Page 19 | Manualshive

Page: 19 / 24

background image

19

TATE DIGITAL WALL MOUNTED MIXER INSTALLATION GUIDE

1

Ensure that the Digital Mixer is installed correctly installed according to the instructions above.

Turn on the water supply and check the unit and plumbing for leaks. Once the plumbing is confirmed to

be water-tight, connect the power supply and conduct the operational test below.

OPERATIONAL TEST

OPERATING THE CONTROL SYSTEM

1 Open

Push the interface once. The interface turns on and the

LED illuminates.

2 Close

Push the interface again. The interface turns off and the
LED goes off.

«
...
17
18
19
20
21
...
»

Summary of Contents for TATE

























Reviews:

No comments

Related manuals for TATE

Brand: Basco Pages: 9

Brand: kelda Pages: 18

Brand: kelda Pages: 21

Brand: Gessi Pages: 24

Pfister Carnegie LG49-WE1

Brand: Spectrum Brands Pages: 6

STRATOS STRX672

Brand: Franke Pages: 8

Brand: ABI INTERIORS Pages: 3

Brand: Hans Grohe Pages: 24

Brand: Rangemaster Pages: 2

Attainable Luxury Quartz

Brand: Zline Pages: 6

Brand: Invacare Pages: 5

Brand: Easylife Pages: 2

Brand: KOLO Pages: 10

Brand: Sanela Pages: 5

Brand: Sanela Pages: 6

Brand: Sanela Pages: 5

Brand: Sanela Pages: 6

Brand: Sanela Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands