TECHNICAL DATA
Drill
DMF23/1150VSE
DMF32/1600VSE
Rated power
W
1150
1600
No load speed
r.p.m
120-480/255-970
130-280/240-510
Bit adaptation cone
Morse
2
3
Maximum capacity in steel mm
23/13
32/16
Maximum capacity in aluminium mm
32/16
50/25
Maximum capacity in wood mm
60/32
80/40
∅
head setting neck
mm 43
63
Approx. weight
Kg.
4.4
5.8
The instructions contained in this manual must be strictly
followed, it should be carefully read and kept close at
hand to use when carrying out maintenance on the
indicated parts.
If the machine is used carefully and normal maintenance
is carried out, it will work well for a long time.
The functions and use of the tool you have bought shall
be only those described in this manual.
Any other use
of the tool is strictly forbidden.
ILLUSTRATIONS
DESCRIPTION (See figures)
B On-/off switch (Fig.1 and 3)
C Retainer button (Fig.1 and 3)
D Mechanical speed shift lever (Fig.1 and 2)
E Auxiliary
grip
(Fig.1)
SAFETY INSTRUCTIONS
•
See “
Safety Instructions
” manual, supplied with this
instruction manual.
•
Warning!
When drilling in amianthus/asbestos
and/or silica stone, the dust produced is extremely
harmful to your health. Wear protection against
inhalation of this dust, in compliance with current
regulations on accident prevention. Follow the in-
surance company’s safety instructions regarding
the responsibility of employees.
•
For your personal safety, always connect the machine
to a mains supply protected by a differential and ther-
mal cut-out switch, in accordance with regulations on
low-voltage wiring sitemaps.
•
Do not perforate the machine casing, as this would
destroy the protective insulation (use adhesive labels).
•
Always unplug the machine before doing any work
on it.
•
Warning!
Before each use, inspect the plug and lead.
Should they need replacing, have this done by an offi-
cial service centre. Only plug the machine in when it is
switched off.
•
Always keep the lead out of the machine’s working
area.
•
Only plug the machine in when it is switched off.
•
Do not allow the machine to get wet, nor should it be
used in wet environments.
•
When using the machine, always wear safety goggles,
gloves and non-slip footwear, and it is advisable to
wear ear protection.
•
Do not touch the bit during or immediately after
working, as it becomes very hot and can cause
serious burns.
•
Hold the machine firmly by the handle and the auxiliary
handle, otherwise the recoil produced could cause the
machine to work imprecisely or even dangerously.
•
Always use the auxiliary handle.
•
Never attempt to clean off dust or shavings resulting
from drilling when the machine is operating.
•
Do not use diamond core bits.
•
When drilling walls, ceilings or floors, take care to
avoid electric wires and gas or water pipes.
BRIEF DESCRIPTION (Mod. DMF32/1600VSE)
The machine is equipped with a safety clutch or mecha-
nism which operates when a bit seizes up, protecting the
user and the machine’s electro-mechanical parts. The
clutch is released automatically.
Warning!
This machine must not be used with hole
saws, core bits, etc, as they tend to jam in the hole
easily. This would cause the safety clutch to trip out
too often.
BEFORE USING THIS TOOL
WARNING!
Before carrying out any work, check, for
instance, using a metal detector, that there are no elec-
tric wires or gas or water pipes under the surfaces you
wish to work on.
Make sure the mains voltage is correct: it must be
the same as that on the specification label. Ma-
chines with 230V can also be connected to a 220-V
mains supply.
To turn the machine on, press the ON/OFF switch
B
and
keep it pressed down.
When the ON/OFF switch is released, the machine
stops.
For permanent operation, press the switch and lock it
(Fig.3) by pushing the retainer button C on the actual
trigger. For accurate drilling it is advisable no to lock
the switch.
WARNING!
Always disconnect the plug from the socket
before doing any work on the machine.
Mains connection
Warning!
Connect only to a single-phase AC current
supply and only to the mains voltage specified on the
rating plate. Connection to sockets without earth protec-
tion is possible as the appliance features protective
class II insulation according to European Standard EN
60745. Radio interference suppression complies with the
European Standard EN 55014.
