background image

Guilin Feiyu Electronic Technology Co., Ltd

 

Guilin Feiyu Electronic Technology Co., Ltd            http://www.feiyudz.cn            E-mail: [email protected]              Page 4

 

This port is use for GPS Receiver. The GPS data protocol is standard NEMA0183. 

Hornet - OSD (V1.6) and DoS connection graph: 

You need a 4p Y line, the Hornet - OSD data line and GPS module connected to the 

DoS’s GPS interface. Connection diagram is as follows:   

 

 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

 

Physical connection diagram:   
Put the 4P Y line inserted into DoS’s GPS port 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Data Radio interface 

The UART pin interfaces consist of: GND, power 5V , TX1, RX1.   
The characteristics as follows: 
Baud Rate: 19200 
Data bits: 8 
Stop Bits: 1 
Parity: None 
Interface Features: TTL level 
This pin interfaces connects to the Data Radio, PC computer serial port or OSD module. 
You can set DoS control parameters and upgrade DoS firmware through this interface. For 
the firmware upgrade,please refer to the firmware update operation manul. 
 

 

GPS module

   

 

 

Hornet OSD module

   

(V1.16) 

 
 

 

(V1.6

版本)

 

OSD

 

data line 

 

Summary of Contents for DoS

















Reviews: