FeiYu Tech DoS Installation & Operation Manual Download Page 7 | Manualshive

Page: 7 / 16

background image

Guilin Feiyu Electronic Technology Co., Ltd

Guilin Feiyu Electronic Technology Co., Ltd http://www.feiyudz.cn E-mail: [email protected] Page 7

and improve the positioning performance of GPS module.

We recommed using suspending damping installation, especially use DoS vibration

absorbing mount which product by FeiYu Tech.(You can find purchase method from FeiYu
official website:

)

Installation process as follows:(You need a allen driver)

1.Use screws to install the four support columns on the baseboard;

2.Stick the solid foam pads (dampers) to the cover board four interior Angle position;

«
...
5
6
7
8
9
...
»

Summary of Contents for DoS

















Reviews:

No comments

Related manuals for DoS

Brand: Skytec Pages: 12

Brand: DAPAudio Pages: 12

Brand: Enapter Pages: 2

Brand: HK Audio Pages: 105

Brand: Grace Digital Pages: 1

Brand: MAJORITY Pages: 32

Brand: RCA Pages: 10

Brand: Essentiel Pages: 57

Brand: THOMSON Pages: 52

Brand: Akai Pages: 23

Brand: Akai Pages: 45

SPORTSOUND 1500HD

Brand: Daktronics Pages: 54

Brand: PondMAX Pages: 8

Brand: AVK Pages: 27

Brand: Cuno Pages: 15

Brand: VacPak-It Pages: 7

Brand: Solargain Pages: 10

Brand: AWE Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands