background image

Guilin Feiyu Electronic Technology Co., Ltd

 

Guilin Feiyu Electronic Technology Co., Ltd            http://www.feiyudz.cn            E-mail: [email protected]              Page 14

 

 

           

Hexa                                  Hexacopter    X                                      Y6

 

                               

 

                 

Octo                                                                Octocopter    X

 

 

Control parameters adjustment 

 

 

RC Sensitivity 

RC  Sensitivity  determine  the  reaction  speed  of  attitude  from  command  stick,  the 

bigger  the  value  the  quicker  the  reaction.  Increase  it  for  sharper  and  quicker  leveling 
action after command stick released. Unstable shaking flying and the control feeling will 
be stiffness and rigid if the value is too high; and sluggish leveling action and slow braking 
if too small. 

 

Control Gain 

Control gain use for stabilizing the flight attitude.

 

To the gains of Pitch and Roll, if 

you  release  the  Pitch  or  Roll  stick  after  command  stick,  multi-rotor  should  be  back  to 
hovering state. 

Summary of Contents for DoS

















Reviews: