background image

Guilin Feiyu Electronic Technology Co., Ltd

 

Guilin Feiyu Electronic Technology Co., Ltd            http://www.feiyudz.cn            E-mail: [email protected]              Page 2

 

 

Auto Return To Launch Mode(RTH) 

The  GPS  Module  must  be  connected  to  the  DoS  with  at  least  5  GPS  satellites 

detected.In this Mode, pitch, roll, yaw and altitude control method is the same as Hovering 
Mode.  Pitch,  roll  sticks  released  will  automatically  fly  the  aircraft  back  to  the  take-off 
point,

 

Maximum return to home point speed:

 

5.5m/s. 

 

Camera Gimbal Stabilization 

DoS  multi-rotor  firmware,when  is  used  to  control  the  aircraft  under  6  axis,  can 

simultaneously control two axis Camera Gimbal Stabilization 

 

 

DoS can connect with the Hornet-OSD and the Data Radio 

DoS has one UART interface for connecting the FY-data radio and the OSD module. 

It can realize the following function by combing them. 

First  Person  View  (FPV):

  Can  be  connected  to  the  Hornet  -  OSD,  the  flight  data 

overlay to video output,and through the vodeo transmission  system to send back, let you 
enjoy the fun of FPV. And it will be easier to operate FPV with the functions of automatic 
balance, Hovering and Auto Return To Launch.   

Real  time  telemetry-real  time  monitor:

  Real  time  telemetry-real  time  monitor  the 

flying state, using the Data Radio to lengthen the remote control distance. 

For more information, please refer to the FY-OSD and FY Data Radio manual. 

1.

 

DoS standard configuration

 

Standard configuration 

●DoS control module *1; 

●RC receiver connecting wires * 1; 

●USB cable *1; 

●Velcro double sided tape * 2; 
 

Optional accessory 

●DoS vibration absorbing mount *1; 

●GPS module *1; 

●Hornet OSD module;   

●Data Radio; 

●Remote Adaptor; 

2.

 

Technical Specification: 

 

DoS module 

Input voltage   

 

 

 

: 4.0 ~ 6.0 Volt; 

Current 

 

 

 

 

 

: 50mA (5V); 

Size     

 

 

 

 

 

: 47 x 30 x 11 mm; 

Weight (excluding wires)  

: 25g; 

Temperature range 

 

 

: -25 ° C ~ +70 ° C; 

Control frequency  

 

 

:400HZ ;                           

Maximum rate of rotation  

: ≤ 2000 °/s. 

 

Summary of Contents for DoS

















Reviews: