background image

IDENTIFICATION 

ID LRU500i 

2  Performance Features 

 

 

Installation 

Page 6 of 35 

 

 

2  Performance Features of ID LRU500i 

Performance Features 

 

2.1  Performance Features 

 

With its compact size, its weather-resistant housing, a read range of 8 to 10 m and the circular-polarized 
antenna supporting any transponder orientation, the UHF Compact Reader ID LRU500i is ideally suited to 
provide efficient and secure vehicle access control. 
The Compact Reader can be easily installed on a VESA mount next to a barrier, gate or bollard due to its 
mechanical construction. The ID LRU500i can be easily integrated into existing access control systems via 
the Wiegand or RS485 interface. A version with Power-over-Ethernet (PoE) and USB is also available. To 
install the compact reader one cable is required for each interface and power supply; for PoE only the 
network cable is required. 

 

2.2  Available Reader Types 

 

The following readers are available: 

Order Number  Reader Type 

Description 

5117.001.00 

ID LRU500i-PoE-EU 

Device version with Power-over-Ethernet and USB for Europe 

5117.001.10 

ID LRU500i-PoE-FCC  Device version with Power-over-Ethernet and USB for North America 

5117.000.00 

ID LRU500i-BD-EU 

Device version with Wiegand interface, RS485 and USB for Europe 

5117.000.10 

ID LRU500i-BD-FCC 

Device version with Wiegand interface, RS485 and USB for North America 

 

 

 

 

Summary of Contents for 5117.000.00




































Reviews: