Feeney DesignRail LED 40W-DK Installation Instructions Manual Download Page 7 | Manualshive

Page: 7 / 11

Feeney DesignRail LED 40W-DK Installation Instructions Manual Download Page 7

1-800-888-2418 | www.feeneyinc.com

7

Step 3A – A

ach Moun

ঞ

ng Plate

A ach the moun ng plate to the post using two of the provided
#8 x 3/4” self-tapping screws

(See Figure 3.1).

Important: Use only the top two moun

ࢼ

ng holes at this

ࢼ

me.

Step 2B – Con

ঞ

nued

For systems with Series 150 top rail:

String an extension cable between each post, feeding it through
the RCB and 1/2" hole, then connect a 2-way spli  er. Feed one
branch of the spli  er out through the 1/2" lead wire pilot hole
drilled in the previous step, this becomes the lead wire for the
light at this post. Feed the other branch of the 2-way spli  er
through the 1/2" hole and the hollow of the RCB and connect
an extension cable

(See Figure 2.4).

Note: A 2-way spli

er does not need to be used at the

fi

nal post, as the

extension cable will connect to the

fi

nal light to complete the circuit.

Use masking tape to temporarily secure lead wire to outside of
post to prevent retrac ng back into post.

Step 3 - Install Post Accent Lights

Figure 2.4

Figure 3.1

EXTENSION
CABLE

LEAD WIRE

2-WAY
SPLITTER

«
...
5
6
7
8
9
...
»

Summary of Contents for DesignRail LED 40W-DK












Reviews:

No comments