1-6
1 - No function assigned
2 - No function assigned
3 - No function assigned
4 - Reset
5 - No function assigned
6 - No function assigned
7 - No function assigned
8 - No function assigned
9 - Radio rebroadcast
10 - Public Address
11 - Wail
12 - Yelp
13 - Hi-Lo
14 - Priority
15 - Manual
16 - Air Horn
17 - No function assigned
18 - No function assigned
19 - No function assigned
20 - No function assigned
Horn Ring Transfer -
No function assigned
RAD
PA
WAIL
YELP
H/L
PRTY
MAN
A/H
17
18
19
20
RESET
2
3
5
6
7
8
1
OFF
Figure 1-2. Keyboard Configuration 3.
14. Switch 14 (PRIORITY).
Press switch 14 to select the priority
siren tone and illuminate the switch 14 LED. Press
switch 14 again to select no siren tone and extinguish
the switch 14 LED.
15. Switch 15 (MAN).
If a siren is not activated, press and
hold switch 15 to sound the peak-and-hold siren tone.
The switch 15 LED is illuminated while the switch is
pressed. The peak-and-hold siren tone sounds as long
as the switch is pressed.
If Mode 2 or Mode 3 is activated (siren
and pattern activated), switch 15 (MAN) operates the
same as the horn ring.
16. Switch 16 (A/H).
In all modes, press and hold switch 16
to sound the air horn tone. The switch 16 LED is
illuminated while the switch is pressed. The air horn
tone sounds as long as the switch is pressed.
17. Switch 17 (JOG LEFT).
Press switch 17 to manually position
activated take-down/alley lights for use as a spot-
light. Each time switch 17 is pressed with a take-
down light activated, the light will move one step to
the left and the switch 17 LED will illuminate
momentarily. Each time switch 17 is pressed with
the alley light(s) activated, the light(s) will move one
step to the rear and the switch 17 LED will illumi-
nate momentarily. Press and hold switch 17 until the
activated light(s) rotates left or rear to the desired
position.
18. Switch 18 (LEFT ALLEY).
Press switch 18 to activate the left
alley light. The LED in the V-shaped display illumi-
nates to simulate, but not necessarily indicate, which
light is activated and the switch 18 LED illuminates.
Press switch 18 again to deactivate the left alley light
and extinguish the switch 18 LED.
19. Switch 19 (RIGHT ALLEY).
Press switch 19 to activate the right
alley light. The LED in the V-shaped display illumi-
nates to simulate, but not necessarily indicate, which
light is activated and the switch 19 LED illuminates.
Press switch 19 again to deactivate the right alley
light and extinguish the switch 19 LED.
20. Switch 20 (JOG RIGHT).
Press switch 20 to manually position
activated take-down/alley lights for use as a spot-
light. Each time switch 20 is pressed with a take-
down light activated, the light will move one step to
the right and the switch 20 LED will illuminate
momentarily. Each time switch 20 is pressed with
the alley light(s) activated, the light(s) will move one
step to the front and the switch 20 LED will illumi-
nate momentarily. Press and hold switch 20 until the
activated light(s) rotates right or forward to the
desired position.
B.
Keyboard Configuration 3
(CLEARBOARD).
NOTE
Refer to figure 1-2 while reading paragraph
1-7.B.
1.
Switch 4 (RESET).
Press this switch to extinguish all
lights (if activated) in the lightbar. The RESET LED
will illuminate and the reflectors rotate to the “home”
position. All other LED’s will extinguish and acti-
vated functions will deactivate.
NOTE
The RESET switch may be pressed at any time
to deactivate any previously selected function(s).
2.
Slide Switch Positions 1, 2, 3, and
Switches 5, 6, 7, 8, 17, 18, 19, 20.
In this keyboard configuration, these
switches are not assigned functions. The installer/
programmer MUST inform you which functions are
assigned to the switches.
