
1-5
d.
Press switch 5 a fourth time to
deactivate the SignalMaster directional signal and
the switch 5 LED will extinguish.
6.
Switch 6 (TAKE-DOWN).
Press switch 6 to activate the take-
down lights. The two lights fitted with clear domes
illuminate and rotate to the take-down (straight
ahead) position. Two LED’s in the V-shaped display
(which represent the take-down lights) will illumi-
nate and the switch 6 LED illuminates. Press switch
6 again to deactivate the take-down lights. The
LED’s in the V-shaped display and switch 6 LED will
extinguish. The take-down lights will return to the
previously activated function, if any.
NOTE
Take-down lights and alley lights can be aimed
or rotated horizontally. Refer to the descrip-
tions for the JOG LEFT and JOG RIGHT
switches below.
7.
Switch 7 (FLASH).
Press switch 7 to activate a four-light
front and rear flashing pattern. Switch 7 also acti-
vates the auxiliary device, such as headlight flashers
or grille lights, connected to the relay A output. The
installer should inform you what device (if any) is
connected to the relay A output. The switch 7 LED
will illuminate. Press switch 7 again to deactivate
the flashing pattern, the auxiliary device, and extin-
guish the switch 7 LED.
8.
Switch 8 (REAR OSCILLATE).
Press switch 8 to activate a four-light,
alternating, oscillating pattern to the rear. The
LED’s in the V-shaped display will flash simulating,
but not necessarily indicating, the lights are acti-
vated and the switch 8 LED illuminates. Press switch
8 again to deactivate the pattern. The LED’s in the
V-shaped display and the switch 8 LED will extin-
guish.
9.
Switch 9 (RAD).
Press switch 9 to activate the radio
rebroadcast function. The switch 9 LED is illumi-
nated. Incoming radio messages are amplified and
rebroadcast by the outside speaker(s). When switch 9
is activated, the radio messages will override all
siren tones and public address operations. Press
switch 9 again to deactivate the radio rebroadcast
function and extinguish the switch 9 LED.
10. Switch 10 (PA).
Switch 10 is used only when the
system is configured for a common microphone. The
installer MUST inform you if the system is config-
ured for a common microphone.
Press switch 10 to activate the PA
function. The switch 10 LED is illuminated. The
user-supplied switching device is energized allowing
microphone audio to be routed to the PA circuits in
the Interface/Relay Unit, instead of the radio trans-
mitter.
Operate the microphone P-T-T (push-
to-talk) switch to broadcast voice messages over the
outside speaker(s). The voice messages will override
any siren tone until the P-T-T switch is released.
NOTE
The PA switch must be activated (common
microphone configuration), when the micro-
phone P-T-T switch is operated, or the
operator’s voice will be broadcast by the radio
transmitter.
If a user-supplied switching device is not used,
the P-T-T switch will override any siren func-
tion and supply public address operation ex-
cept when switch 9 (RAD) is activated.
Press switch 10 again to deactivate the
PA function and extinguish the switch 10 LED.
IMPORTANT
In this keyboard configuration, the siren tones
DO NOT sound unless Mode 2 or 3 is also
activated.
11. Switch 11 (WAIL).
The switch 11 LED is illuminated and
the wail siren tone is selected. Press switch 11 to
select no siren tone and extinguish the switch 11
LED. Press switch 11 again to select the wail siren
tone and illuminate the switch 11 LED.
12. Switch 12 (YELP).
Press switch 12 to select the yelp siren
tone and illuminate the switch 12 LED. Press switch
12 again to select no siren tone and extinguish the
switch 12 LED.
13. Switch 13 (H/L).
Press switch 13 to select the hi-lo siren
tone and illuminate the switch 13 LED. Press switch
13 again to select no siren tone and extinguish the
switch 13 LED.