background image

6

  

  

1. Configuring the Network Interface

Informer15 Speaker (Models I-IP15 and I-IP15X) Modbus Enabled 

Federal Signal www.fedsig.com

Programming with Commander

The following capabilities are only available if programmed from the factory or via 

Commander. Functions which combine multiple actions together can be activated via 

Modbus. In addition, the IP15 has inputs to locally activate the unit. These inputs require 

programming from the factory or via Commander

1. 

Programming Functions–Functions are a set of specific instructions for an 

Informer15. Functions are typically used when a number of actions are always used 

together (for example, with relay activations, volume level, multiple voice messages, 

use ambient noise level, and so forth.) Functions are defined at time of order and are 

programmed in the unit at the factory. A Modbus address or register is assigned to 

these functions for activation.

2. 

Programming Local Physical Inputs–The Informer15 has four inputs that can be used 

to notify the Modbus controller of an activation. In addition, the local activation input 

can activate the speaker to perform a single action or a set of actions (for example, 

relay, light, tone, voice, and so forth.)

1. Configuring the Network Interface

The procedures in this section apply to the following informer:
•  Informer15 Speaker (I-IP15)

Configuring the Network Interface through the Web Browser

The System Administrator identifies the server IP address, Subnet Mask, Default 

Gateway, and the IP addresses for all Informer devices.
If the configuration details are lost or changed incorrectly and it becomes necessary 

to restore the Informer to factory default settings, see the “Restoring Configuration to 

Factory Defaults” on page 15. 

Login

To configure the network interface through the web browser:

1. 

Prior to installing Informer devices on an IP network, connect your PC to the 

Informer device using a LAN cable. Turn on the Informer device.

2. 

Change your Local Area Connection (Ethernet) adapter address to the following:

IP Address: 10.10.10.10
Subnet Mask: 255.255.0.0
Default Gateway: 10.10.10.10

 

This allows you to access the Informer at its default IP address (10.10.10.1).

Summary of Contents for Informer15 Series





















Reviews: