background image

16

  

  

2. Digital Voice or Tone Files

Informer15 Speaker (Models I-IP15 and I-IP15X) Modbus Enabled 

Federal Signal www.fedsig.com

Logging Out of the Web Interface

Use the Log Out page to log out before the five minute session timer expires.
To log out of the web interface, do the following:

1. 

Select Log Out. 

The Log Out page appears.

2. 

Click the Log Out button to logout.

2. Digital Voice or Tone Files

You can load Informers with WAV files for broadcasting. Federal Signal can provide 

high-quality voice and/or tone WAV file. WAV files are stored on a microSD card, which 

is accessible in the junction box of the speaker.
The WAV files must be mono 8 bit, 8 kHz format. To store files on the Informer15, 

remove the microSD card from the unit. Using a PC, store the WAV files using the 

naming convention of DV1.wav, DV2.wav, and so forth.

NOTE

: 2 GB FAT16 formatted SD cards support up to 250 WAV files. 4 GB or larger 

FAT32 formatted SD cards support up to 4093 messages.

3. Operation

This section covers the Modbus data structure and associated functions that can be 

performed.

Modbus Control Systems (I-IP15)

The software versions listed below are the minimum versions that support the Modbus 

interface. A firmware upgrade will be required to use the Modbus interface if the RTU 

firmware is below these minimum requirements.
•  DIGI v1.2.0.5
•  IP15 v2.2.0.7

Summary of Contents for Informer15 Series





















Reviews: