background image

6

  

  

Installation and Maintenance Instructions

Models 151XST and 151XST-S

Failure to follow all safety precautions and instructions may result 

in property damage, serious injury, or death.

An Overview of the 151XST Series

Federal Signal’s Model 151XST hazardous location strobe light 

provides 80 high-intensity flashes per minute. This warning light is 

available in 12-24 Vdc, 120 Vac and 240 Vac, 50/60 Hz.
The Model 151XST strobe light is UL Listed and CSA Certified 

for Class I, Division 2, Groups A, B, C and D; Class II, Division 1, 

Groups E, F and G; and Class III.
The 151XST meets Type 4X water-tight, dust-tight, and corrosion-

resistant requirements; constructed to IP66. This hazardous 

location warning light has an aluminum base, coated for corrosion 

resistance that is ready for mounting on a 3/4-inch NPT pipe.  

The included dome guard fits over the glass dome to protect it 

against accidental collision with moving equipment, such as 

forklifts. An optional wall bracket is also available.
The 151XST has an effective candela (ECP) of 165 and a 520,000 

peak candela. It is available in six dome colors, including amber, 

blue, clear, green and red (magenta upon request).
Federal Signal’s rugged 151XST strobe warning light is 

specifically designed for hazardous locations or corrosive 

environments where a very bright visual signal is required. 

This warning light can be used for plant evacuation or other 

communication needs. 
Models are available for pipe mounting (151XST) or surface 

mounting (151XST-S).

NOTE:

 The Model 151XST can be mounted to a Federal 

Signal Model LHWB bracket. If installed in this way, the entire 

assembled device is suitable only for Class I, Div. 2, Groups A, B, 

C, and D; Class II, Div. 2, Groups F and G; Class III locations.

Summary of Contents for 151XST Series





















Reviews: