FC Curtis NX Series Operator'S Manual Download Page 15

Page: 15 / 48

CAP-835

3.2 Requirements in the

installation location

Set up the screw compressor so that the
following conditions are fulfilled:

◼

The installation location is level.

◼

The machine is easily accessible and can be
accessed from all sides.

◼

There is sufficient lighting.

◼

There is sufficient ventilation.

◼

There is a power supply available.

◼

Escape paths and rescue equipment are
freely accessible.

◼

The machine is not subjected to an explosive
atmosphere.

◼

The machine is not subjected to a corrosive
atmosphere.

◼

The machine is not subjected to direct solar
radiation.

◼

Outside heating from surrounding heat
sources is excluded.

◼

There is no dust accumulation.

◼

Fire protection measures have been taken.

◼

The machine is not subjected to vibrations.

◼

The floor is resistant to solvents,
impermeable to liquids, anti-static and easy
to clean.

◼

There are no machines in the vicinity that
cause electrical or electromagnetic
disturbance.

3.3 Installation

3.3.1

Remove shipping spacers

To protect the vibration isolators underneath the
motor/airend assembly during transport, there
are red spacers that hold the assembly in place.

Make sure all of these spacers are removed
before first startup of the compressor.

Failure

to remove the spacers will result in excessive
vibration and can cause damage to the
compressor.

Fig.6 : Shipping spacer

3.3.2

Ventilation

DANGER!
Risk of fatal injury from the use
of explosive gas mixtures,
vapors, dust or aggressive
hazardous substances!

The use of explosive gas mixtures,
vapors, dust or aggressive
hazardous substances to ventilate
the screw compressor can cause
severe or even fatal injuries as well
as significant material damage.
- Never use explosive gas

mixtures, vapors, dust or
aggressive hazardous
substances to ventilate the
screw compressor.

- Make sure that no potentially

explosive gas mixtures, vapors,
dust or aggressive hazardous
substances enter into the
ventilation for the screw
compressor.

The air fed via the intake openings is used for
compression and for cooling the machine.

Summary of Contents for NX Series

















































Search results

Summary of Contents for NX Series

Reviews:

Related manuals for NX Series

Brands by name

Popular brands

FC Curtis NX Series, Operator'S Manual

Search results

Summary of Contents for NX Series

Reviews:

Related manuals for NX Series

Brands by name

Popular brands