background image

 

 

17 

www.fastTT.bike 

FastTT Aero Bar Installation Guide - TKP v8 

WARRANTY

 

FastTT Aero Bars are lightweight carbon competition units. In the event of a fall or harsh 

impact, please check the bars carefully for any visible damage. Whilst carbon fibre is 

exceptionally strong, it does not tolerate impacts, and damage that is invisible to the naked 

eye can occur. This could result in unexpected breakage and injury, even death. If in doubt, 

please have your bars checked by a reputable carbon repair company. 

 

The manufacturer (Bold Horizon Ltd t/a FastTT) assumes no responsibility or liability for any 

injury, loss or damage caused as a result of using this product under any conditions. FastTT 

Aero Bars are supplied with a 24-month manufacturers defect warranty. Any damage caused 

by misuse, incorrect installation, modification, accident, or any other cause is not covered by 

the manufacturer’s warranty. 
 

In the event of a warranty claim the manufacturer reserves the right to replace, repair or credit 

the full purchase price excluding shipping (where applicable). In the event of a replacement or 

repair, the cost of returning the unit to the manufacturer will be paid by the customer. The 

manufacturer will pay for shipping of the repaired or replacement unit to the customer. 

 

SPECIFICATIONS AND INSTALLATION INSTRUCTIONS 

Specifications and installation instructions are subject to change without notice. To the best of 

our knowledge, all information is correct at time of publishing The manufacturer is not 

responsible for changes to UCI technical regulations. It is the customer’s responsibility to 

remain informed of any rule changes and to make the necessary changes to bike setup for 

compliance.  

 

CRASH REPLACEMENT COMMITMENT 

If you're unfortunate enough to have a crash and damage your FastTT aero bars where they're 

no longer safe to use, send them back to us and we'll replace them with a brand new set at 

50% off the current retail price, including free shipping. It's tough enough crashing, but at least 

we can help a little to ease your pain. 

Contact us via email: [email protected] or message us on Instagram: @fastTT.bike 

 

 

Copyright © 2022 FastTT - The Sports Product Division of Bold Horizon Ltd 

SECTION F – WARRANTY AND DISCLAIMER

 

Summary of Contents for Track Pursuit Aero Bar


















Reviews: