background image

 

 

Commissioning 

 

 

Installation instructions 

23 

 

Improper  
operation 

 

 

WARNING! 
Improper operation can lead to serious injuries 

Therefore: 

–  Read and follow the operating manual. 

 

Danger of fire 

 

 

WARNING! 
Danger of injury due to fire 

Objects on the oven or near the oven can cause fire and thus lead to in-
juries. 

Therefore: 
–  Always keep the oven and its surrounding free of objects. 

 

Health hazards 

 

 

WARNING! 
Danger of injury due to covering of the temperature sensor and/or 
humidity sensor 

Covering the temperature sensor and/or the humidity sensor can lead to 
increased temperature and humidity. The increased values can lead to 
health hazards or to serious injuries. 

Therefore: 

–  Do not cover the temperature and humidity sensor. 
–  Ensure unrestricted air circulation.  

 

Accessories 

 

 

WARNING! 
Danger due to incorrectly connected devices! 

Devices and accessories from other manufacturers may be connected 
to this control if the technical data match. These devices have their own 
operating instructions. 
Please note the safety information, technical data and instructions in the 
operating instructions of connected devices. 

 

 

6.2 

Checks before the initial commissioning 

 

 

The following points should be checked before the initial commissioning: 

 

Does the voltage supply match the specifications on the nameplate? 

 

Have the cable specifications as per Table 2, page 8 and the electrical circuit dia-
gram 

Fehler! Verweisquelle konnte nicht gefunden werden.

, page 19 been ad-

hered to? 

 

Is the control device connected as per the electrical circuit diagram? 

 

Are the sensors (temperature and humidity) connected as per section 

Fehler! Ver-

weisquelle konnte nicht gefunden werden.

, page 

Fehler! Textmarke nicht 

definiert.

 ff? 

 

Have all the neutral conductors been laid on the N- bus bar in the sauna control de-
vice? 

 

Have all the earthing conductors been laid on the PE-bus bar in the sauna control 
device? 

 

Have all the screws been tightened correctly? 

 

Summary of Contents for FNT2000 Series





























Reviews: