FarmTek Growers Supply GrowSpan Gothic Pro 113836R Manual Download Page 28

Page: 28 / 59

GROWSPAN

™

GOTHIC PRO GREENHOUSES AND SYSTEMS

113836_37_38_39R Revision date: 06.06.18

POLYCARBONATE ROOF PANELS (continued)

7. Using FA4484B Tek screws and 102921 neo-bonded

washers, attach panel to rafters. Use assistants and

hand clamps as needed to hold panel tight to rafters as

screws are installed.

Ensure panel remains square on frame during

installation. Next panels will not align properly if first

panel is improperly installed.

If panel does not align, check that rafters are spaced at

48" on-center from ground post along one side to those

on opposite side.

Adjust rafters as needed.

Duct tape can be used in small pieces to hold

H-channel in place along panel edges. Do not allow to

work loose during installation. H-channel to remain tight

to panel edge.

IMPORTANT:

Space screws at 16" on-center. Install

last screws at top of panel 7" from panel end to

allow space for upper panel to overlap when it is

installed.

Vent Tape Bottom

Foil Tape

Top

IMPORTANT:

Do not over-tighten Tek screws. Install

snug. Screws should not distort or crush panel cells or

H-channel.

6. With assistance, place panel against frame and align center of H-channel with center of second rafter.

Position end

with foil tape at top.

Verify you have UV-protected surface of panel facing toward sun. (Panel was marked earlier

during preparation—Step 1.)

Summary of Contents for Growers Supply GrowSpan Gothic Pro 113836R




























































Search results

Summary of Contents for Growers Supply GrowSpan Gothic Pro 113836R

Reviews:

Related manuals for Growers Supply GrowSpan Gothic Pro 113836R

Brands by name

Popular brands

FarmTek Growers Supply GrowSpan Gothic Pro 113836R, Manual

Search results

Summary of Contents for Growers Supply GrowSpan Gothic Pro 113836R

Reviews:

Related manuals for Growers Supply GrowSpan Gothic Pro 113836R

Brands by name

Popular brands