FarmTek Growers Supply GrowSpan Gothic Pro 113836R Manual Download Page 14

Page: 14 / 59

GROWSPAN

™

GOTHIC PRO GREENHOUSES AND SYSTEMS

113836_37_38_39R Revision date: 06.06.18

SIDE STRUT INSTALLATION

There are four (4) side struts for the shelter. These struts

are positioned between the end rafters and the first interior

rafter on each side. Complete these steps to install the four

(4) side struts:

Gather parts:
•  Struts
•  Band Clamps (#QH1402)
•  Lag screw or nut and bolt (supplied by customer)

1. Locate one strut and position it between end rafter and

first interior rafter as shown below.

Strut

End Rafter

Interior

Rafter

Baseboard is required

for this procedure.

Customer supplies the

baseboard.

2. Attach one end of strut to band clamp as shown.

Strut

End Rafter

Band Clamp

3. Attach remaining end of strut to baseboard using a lag

screw or nut and bolt (not included). See diagram that

follows for location.

NOTE:

A baseboard provides a place to attach each

strut and helps keep ground posts at the required

depth. Customer is responsible for providing a

baseboard for this frame. If no baseboard is present,

attach strut to ground post using a FA4484B Tek

screws or other customer-supplied fasteners.

4. Repeat above steps to attach the remaining side struts.
5. After securing struts, verify that each clamps is secured

with a FA4482B Tek screw to the rafter.

6. Verify that each pipe splice (purlin and rafter) is

secured with an FA4482B Tek screw.

7. Complete the next procedure to anchor the assembled

frame.

ANCHOR THE ASSEMBLED FRAME

At this point, anchor the greenhouse frame. Consult the

MUST READ document for anchoring information and

suggestions. Please call customer service at 1-800-245-

9881 for additional anchoring information.

CAUTION

: The anchor assembly is an integral part of

the greenhouse construction. Improper anchoring may

cause instability and failure of the structure to perform

as designed. Failing to anchor the shelter properly

will void the manufacturer’s warranty and may cause

serious injury and damage.

Photo shows the strut attached

to the inside of the customer-

supplied baseboard.

Attach strut

as shown.

End

Rafter

Finished Grade

Baseboard

NOTE:

Head of bolt on band clamp must face toward

the outside of shelter.

Finished Grade

Summary of Contents for Growers Supply GrowSpan Gothic Pro 113836R




























































Search results

Summary of Contents for Growers Supply GrowSpan Gothic Pro 113836R

Reviews:

Related manuals for Growers Supply GrowSpan Gothic Pro 113836R

Brands by name

Popular brands

FarmTek Growers Supply GrowSpan Gothic Pro 113836R, Manual

Search results

Summary of Contents for Growers Supply GrowSpan Gothic Pro 113836R

Reviews:

Related manuals for Growers Supply GrowSpan Gothic Pro 113836R

Brands by name

Popular brands