FarmTek Growers Supply GrowSpan Gothic Pro 113836R Manual Download | Manualshive

Page: 4 / 59

background image

GROWSPAN

™

GOTHIC PRO GREENHOUSES AND SYSTEMS

4

113836_37_38_39R Revision date: 06.06.18

BASEBOARDS FOR FRAME — RECOMMENDED

These instructions describe installing a baseboard

(recommended) at ground level along each side of the

frame. Baseboard runs from front to back of frame.

This baseboard is

not included

and is customer supplied.

When installed properly the baseboard helps prevent

ground posts from sinking when anchored. Depending

on building, it also provides a surface to attach struts or

other building components.

Secure baseboard using the

supplied FAH009B (1/4" x 4") bolts and FALB01B (1/4")

nuts.

Consult these instructions, or contact Customer Service for

additional information regarding baseboards.

Dotted line represents the anti-billow rope.

Example: Circles identify the ends of Rope #1.

ANTI-BILLOW ROPE INSTALLATION

TO PREVENT DAMAGE AND POSSIBLE INJURY,

INSTALL THE ANTI-BILLOW ROPES IN SHORT

LENGTHS ALONG EACH SIDE OF THE FRAME.

DO NOT INSTALL AS A SINGLE LENGTH TIED AT

EACH END OF THE BUILDING. DOING SO WILL

RESULT IN A LOOSE SIDE PANEL IF THE SINGLE

ROPE BREAKS DURING STRONG WINDS.

Rope

#1

Rope

#2

Rope

#3

REQUIRED TOOLS

The following list identifies main tools needed to

assemble shelter. Additional tools and supports may also

be required.
• Tape measure or measuring device; marker to mark

locations on the pipes

• Variable speed drill and power driver (cordless with

extra batteries works best)

•  Metal-cutting saw; drill and drill bits
•  Wrenches and socket set, or adjustable wrenches
•  Scissors, utility knife, or tin snips; flat bar or putty knife
•  Chalk line & caulk gun to apply sealant
•  Hammers and gloves; adjustable and self-locking pliers
•  Ladders, work platforms, and other machinery for lifting

designed to work safely at height of building

• Rope/cable for cover installation

UNPACK AND IDENTIFY PARTS

The following steps will ensure you have the necessary

parts

before

you begin.

1. Unpack the contents of the shipment and place where

you can easily inventory the parts. Refer to the Bill of

Materials/Spec Sheets.

2. Verify that all parts listed on the Bill of Materials/Spec

Sheets are present. If anything is missing or you have

questions, consult the Pictorial Parts Guide and all

diagrams for clarification, or contact Customer Service.

NOTE:

At this time, you do not need to open the plastic

bags containing smaller parts such as fasteners or

washers (if equipped).

RECOMMENDED DIMENSIONS:

•

2" x 6"

(minimum) treated or recycled plastic lumber

(supplied by customer).

«
...
2
3
4
5
6
...
»

Summary of Contents for Growers Supply GrowSpan Gothic Pro 113836R




























































Reviews:

No comments

Related manuals for Growers Supply GrowSpan Gothic Pro 113836R

Cross Country Arctic Series

Brand: ACF Greenhouses Pages: 52

Brand: Dancover Pages: 31

Brand: ACD PRESTIGE Pages: 47

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands