FarmTek Growers Supply GrowSpan 106310D Manual Download

Page: 32 / 53

GROWSPAN

™

GOTHIC PRO GREENHOUSES AND SYSTEMS

Revision date: 05.29.19

Axle Conduit

13. Verify that the pipe is level and secure the band clamp

to the underside of the second rafter using an FA4484

Tek screw. Pipe should remain loose in the band clamp.

Band clamps support the axle conduit at each rafter

except the end rafter where the gearbox is mounted.

14. Take a section of 131S075 pipe, attach it to the first,

and secure the connection using one Tek screw.

15. Slide another band clamp onto the tapered/swaged end

of the conduit, level the conduit, and secure the band

clamp to the underside of the next rafter.

16. Continue adding conduit and band clamps and work

toward the other end of the shelter. Verify that the axle

conduit remains level throughout the length.

Attach one

band clamp to the inside of each rafter.

17. Select the final section of plain pipe (131P0XX where

XX represents the length needed to reach the end of

your building. Consult side profile diagram for pipe

identification.)

NOTE:

Do not allow the free end of the axle to touch

the inside surface of the end wall. Trim pipe if needed.

Axle must turn freely.

18. After installing all sections of axle conduit for the first

drop-down curtain assembly, verify that the axle conduit

is level and that each conduit splice is secured with a

Tek screw (Step 14).

19. Move to the gearbox and test the assembly using the

crank handle.

NOTE:

The assembled axle conduit should turn freely

throughout the length of the shelter. Adjust the band

clamps as needed. Reposition clamps and screws if

these prevent smooth operation of the axle conduit.

20. After verifying that the axle turns smoothly, repeat the

procedure to assemble and attach the gearbox and

axle conduit

to the other side of the shelter.

21. Continue by preparing and attaching the drop-down

curtains to the frame and axle conduit of both drop-

down assemblies.

INSTALL THE DROP-DOWN CURTAIN (continued)

Interior Rafter

Axle Conduit

106734 Band

Clamp

As seen from

the inside.

Photo shows the

fully assembled

drop-down

curtain from

the inside of a

sample shelter.

Curtain is

installed later.

Axle Conduit

Ribbon Board

As seen from

the inside.

Band Clamp

Summary of Contents for Growers Supply GrowSpan 106310D






















































Search results

Summary of Contents for Growers Supply GrowSpan 106310D

Reviews:

Related manuals for Growers Supply GrowSpan 106310D

Brands by name

Popular brands

FarmTek Growers Supply GrowSpan 106310D, Manual

Search results

Summary of Contents for Growers Supply GrowSpan 106310D

Reviews:

Related manuals for Growers Supply GrowSpan 106310D

Brands by name

Popular brands