FarmTek Growers Supply GrowSpan 106310D Manual Download

Page: 25 / 53

GROWSPAN

™

GOTHIC PRO GREENHOUSES AND SYSTEMS

Revision date: 05.29.19

DOUBLE DOOR ASSEMBLY (continued)

12. After end cap profile is installed, install another section

of the same end cap on the

inside frame of the door

that includes the chain latch.

Diagram may show a different frame used for illustration

purposes only.

NOTE:

This length of end cap will act as a stop for the

remaining door of the double door assembly when both

doors are closed.

13. Check the operation of the latches and the doors.
14. Continue with the

Main Cover Installation

procedure

that follows.

MAIN COVER INSTALLATION

After the end panels and doors are installed, install the

main covers. The steps to install the cover include:
1. Attach poly latch U-channel along the greenhouse

sides and tops of the greenhouse

end rafters

2. Pull one cover film over the frame and attach to the end

rafters.

3.  Stretch and attach the first cover to the sides.
4.  Install the Inflation Fan kit.
5.  Attach a second cover layer to the frame.
6.  Test the operation of the Inflation Fan kit.

INSTALL POLYLATCH U-CHANNEL (102197)

Gather parts:

• Aluminum U-Channel (#102197)
• Ribbon board - 2" x 6" (see

Page 29

)

• Wood screws (FA4652) & 1/4" x 4" carriage bolts
1. Measure height (48" maximum) to identify top of drop-

down sides. Attach poly latch channel at approximately

48" above ground on both sides of the frame.

Attaching a ribbon board (not included) to the

rafters and then attaching the poly-latch u-channel

to the ribbon board using wood screws is required.

Consult the diagram below for clarification.

NOTE:

Required ribbon board and baseboard shown

in the diagram above

are not included

and are supplied

by the customer.

2. Attach one section of poly latch U-channel to ribbon

board using FA4652 wood screws. Attach U-channel

flush with outside edge of the end wall panels.

Space

screws at 16" on-center throughout length.

NOTE:

Single poly latch (102197) is attached to

building sides and tops of end rafters.

Rafter

2" x 6" Board

1" x 4" Board

(Installed later in

these instructions)

1/4" x 4"

Carriage

Bolts

U-Channel

Side View

48"

Ribbon Board

Rafter

Summary of Contents for Growers Supply GrowSpan 106310D






















































Search results

Summary of Contents for Growers Supply GrowSpan 106310D

Reviews:

Related manuals for Growers Supply GrowSpan 106310D

Brands by name

Popular brands

FarmTek Growers Supply GrowSpan 106310D, Manual

Search results

Summary of Contents for Growers Supply GrowSpan 106310D

Reviews:

Related manuals for Growers Supply GrowSpan 106310D

Brands by name

Popular brands