FarmTek Growers Supply GrowSpan 106310D Manual Download

Page: 7 / 53

GROWSPAN

™

GOTHIC PRO GREENHOUSES AND SYSTEMS

Revision date: 05.29.19

End Rafter

Interior

Rafter

Baseboard is

supplied by

customer.

Ground

Level

ATTENTION:

Position purlins evenly during the

frame assembly. Use the rafter pipe joints as

guides when installing the end clamps, cross

connectors, and purlins.

Purlins

Ground

Post

Chord

OVERVIEW

This section describes assembling your greenhouse. For

details, please see section, Assembling the Gothic Pro

Greenhouse Components. See illustration below to identify

main parts of greenhouse.
1.  Locate the required parts for each assembly procedure.
2.  Assemble the rafters and frame, and square the frame.
3.  Prepare and attach end panels.
4.  Install main cover.
5.  Attach the drop-down curtain and

anti-billow ropes.

Ribbon

Board

GrowSpan

™

Gothic Pro Greenhouses and Systems

Summary of Contents for Growers Supply GrowSpan 106310D






















































Search results

Summary of Contents for Growers Supply GrowSpan 106310D

Reviews:

Related manuals for Growers Supply GrowSpan 106310D

Brands by name

Popular brands

FarmTek Growers Supply GrowSpan 106310D, Manual

Search results

Summary of Contents for Growers Supply GrowSpan 106310D

Reviews:

Related manuals for Growers Supply GrowSpan 106310D

Brands by name

Popular brands