FarmTek Growers Supply GrowSpan 106310D Manual Download

Page: 14 / 53

GROWSPAN

™

GOTHIC PRO GREENHOUSES AND SYSTEMS

Revision date: 05.29.19

SIDE STRUT INSTALLATION

There are four (4) side struts for the shelter. These struts

are positioned between the end rafters and the first interior

rafter on each side of the shelter.

Complete these steps to install the four (4) side struts:

Gather the Parts
•  Struts
•  Band Clamps (#QH1402)
•  Lag screw or nut and bolt (supplied by customer)
1.  Locate one strut and position it between one end rafter

leg and the leg of the first interior rafter as shown

below.

Strut

End Rafter

Interior

Rafter

Baseboard is required

for this procedure.

Customer supplies the

baseboard.

Ground Level

2. Attach one end of the strut to the band clamp as shown

in the diagram below.

Strut

End Rafter

Band Clamp

3. Attach the remaining end of the strut to the baseboard

using a lag screw or nut and bolt (not included). See

the diagram that follows for location.

NOTE:

A baseboard provides a place to attach each

strut and helps keep the ground posts at the required

depth. The customer is responsible for providing a

baseboard for this frame.

4. Repeat the above steps to attach the remaining side

struts to the shelter.

5. After securing the struts, verify that all clamps are

secured with a Tek screw to the rafters.

6. Verify that each pipe splice (purlin and rafter) is

secured with a Tek screw.

7. Complete the next procedure to anchor the assembled

frame.

ANCHOR THE ASSEMBLED FRAME

At this point, anchor the greenhouse frame. Consult the

MUST READ document for anchoring information and

suggestions. Please call customer service at 1-800-245-

9881 for additional anchoring information.

CAUTION

: The anchor assembly is an integral part of

the greenhouse construction. Improper anchoring may

cause instability and failure of the structure to perform

as designed. Failing to anchor the shelter properly

will void the manufacturer’s warranty and may cause

serious injury and damage.

NOTE:

Head of bolt on the band clamp must face the

toward the outside of the shelter.

Photo shows the strut attached

to the inside of the customer-

supplied baseboard.

Attach strut

as shown.

End

Rafter

Ground Level

Baseboard

Inside of

frame.

Summary of Contents for Growers Supply GrowSpan 106310D






















































Search results

Summary of Contents for Growers Supply GrowSpan 106310D

Reviews:

Related manuals for Growers Supply GrowSpan 106310D

Brands by name

Popular brands

FarmTek Growers Supply GrowSpan 106310D, Manual

Search results

Summary of Contents for Growers Supply GrowSpan 106310D

Reviews:

Related manuals for Growers Supply GrowSpan 106310D

Brands by name

Popular brands