FarmTek FodderPro 2.0 Micro System Manual Download Page 4

Page: 4 / 43

111628M

Revision date: 09.25.18

PICTORIAL GUIDE

The following graphics and photos will help identify the different

parts of the fodder system. (Some parts may not be shown.)

Quantity when noted is in ( ) following the stock number.

111485 (16)

104626 (2)

104627 (8)

104625 (4)

FA4482B

Tek Screw

FA4472B (6)

Tek Screw

112502 Carriage Bolt (8)

FALB08B Nut (16)

FALB04B 3/8"

Nuts (6)

FAME09B Flat

Washer (16)

111906 1" Sammy

for 3/8" Threaded rod (2)

Components for hanger brackets: FAK26 threaded

rods (2), 111907 conduit hangers (2), and FALB04B

nuts (3 per bracket assembly).

ATTENTION:

Drill the mounting hole in the 111907

hanger bracket to 7/16" if needed to accept the 3/8"

threaded rod.

Exercise caution.

Clamp the hanger

bracket in a vice before drilling!

100441 (2) Nut Setter

100442 (1) Nut Setter

111907

Important Information

(12)

S15P048 @ 48"

(16) S15P027 @ 27"

(2) 111628A @ 55 3/4" drilled (End Frame)

Summary of Contents for FodderPro 2.0 Micro System












































Search results

Summary of Contents for FodderPro 2.0 Micro System

Reviews:

Related manuals for FodderPro 2.0 Micro System

Brands by name

Popular brands

FarmTek FodderPro 2.0 Micro System, Manual

Search results

Summary of Contents for FodderPro 2.0 Micro System

Reviews:

Related manuals for FodderPro 2.0 Micro System

Brands by name

Popular brands