FarmTek FodderPro 2.0 Micro System Manual Download Page 8

Page: 8 / 43

111628M

Revision date: 09.25.18

ASSEMBLE MAIN FRAME: Support Frames

Gather the parts and complete the steps that follow to

assemble the two (2) support frames.

Required parts for

each support frame

•  (1) Assembled base rail (from previous page)
•  (4) 104627 4-Way Connectors
•  (1) S15P048 Square Tube (plain) for vertical support
•  FA4482B Tek Screws and 100441 Magnetic Nut Setter

ATTENTION:

Install Tek screws as shown for best results and a uniform

appearance.

Review all diagrams for clarification.

Complete these steps:
1. Take the S15P048 tube and slide one 4-way connector onto one end.

Slide the end of the tube into the 3-way connector of the base rail and

secure using two (2) Tek screws (Fig 1).

2. Using the diagram to the right, position the 4-way connector as shown

and secure to the vertical tube using two (2) Tek screws (Fig. 2).

3. Move to the top of the vertical tube and slide three (3) more 104627

connectors onto the tube (Fig. 3).

4. Using the diagram to the right and in the Quick Start section, space each

connector on the tube and secure using two (2) Tek screws (Fig. 4).

5. Repeat the steps to assemble the remaining support frame.
6. Continue with the next procedure.

Assembly Instructions

8" between

connectors.

This level only.

FA4482B

Tek Screws

S15P048

9-3/4" between

connectors.

Assembled Base Rail with Levelers

FIG. 1

FIG. 3

FIG. 4

FIG. 2

Summary of Contents for FodderPro 2.0 Micro System












































Search results

Summary of Contents for FodderPro 2.0 Micro System

Reviews:

Related manuals for FodderPro 2.0 Micro System

Brands by name

Popular brands

FarmTek FodderPro 2.0 Micro System, Manual

Search results

Summary of Contents for FodderPro 2.0 Micro System

Reviews:

Related manuals for FodderPro 2.0 Micro System

Brands by name

Popular brands