FarmTek FodderPro 2.0 Micro System Manual Download Page 34

Page: 34 / 43

111628M

Revision date: 09.25.18

Quick Start Guide: Additional Drain Manifold Photos

Photos on this page show the assembled drain manifold as attached to the frame. (Manifold can be assembled on a flat surface and

then attached to the frame to allow easier adjustment of the manifold height on the frame if desired.) Dry fit all manifold components

before you secure the horizontal tubes to the 111696 cross fittings only. Coat the outside of one end of a tube and the inside of

fitting with PVC primer and cement. Slide tube into the 111696 fitting. Gently lift the open end of the tube to create a slight slope

toward the center stack. Allow the cement to set and release the tube. Repeat for all remaining horizontal tubes. Install the slip

caps.

Do not secure the slip caps to the ends of the horizontal tubes.

These must remain free to remove so the horizontal

tubes can be cleaned.

Summary of Contents for FodderPro 2.0 Micro System












































Search results

Summary of Contents for FodderPro 2.0 Micro System

Reviews:

Related manuals for FodderPro 2.0 Micro System

Brands by name

Popular brands

FarmTek FodderPro 2.0 Micro System, Manual

Search results

Summary of Contents for FodderPro 2.0 Micro System

Reviews:

Related manuals for FodderPro 2.0 Micro System

Brands by name

Popular brands