background image

49 

50

SERVICING AND WARRANTY CONDITIONS

16  SERVICING AND WARRANTY CONDITIONS

16.1 Servicing

Servicing is secured by the dealer after consulting with the manufacturer, possibly directly by the manu-

facturer.  Spare  parts  then  using  the  sales  network  by  individual  sellers  in  the  entire  country.  Use  only  the 
spare parts according to the spare parts catalogue officially issued by the manufacturer.

16.2 Warranty

1. 

The  manufacturer  provides  a  warranty  of  24  months  for  these  machine  parts:  main  frame,  axle, 
and  machine  tow  bar.  For  other  parts  of  the  machine, the  manufacturer  provides  a  warranty  of  12 
months.  The  warranty  is  provided  from  the  date  of  sale  of  the  new  machine  to  the  end  user 
(consumer).

2. 

The  warranty  applies  to  hidden  defects  that  will  show  in  the  warranty  period  with  proper  use  of 
the machine and while fulfilling the conditions stated in the operating manual.

3. 

The  warranty  does  not  apply  to  wearable  spare  parts,  i. e.  regular  mechanical  wear  and  tear  of 
replaceable parts of the working sections (shares, edges, etc.).

4. 

The  warranty  does  not  apply  to  indirect  consequences  of  possible  damage,  such  as  service  life 
decrease etc.

5. 

The warranty is bound to the machine and is not void upon an owner change.

6. 

The  warranty  is  limited  to  the  disassembly  and  assembly,  possibly  replacement  or  repair  of  the 
defective part.  The decision, whether to replace or repair the defective part, is up to the contractual 
workshop of Farmet.

7. 

During  the  warranty  period,  only  the  authorised  servicing  technician  of  the  manufacturer  may 
perform repairs or other interventions into the machine. In the opposite case, the warranty will not 
be  acknowledged.  This  provision  does  not  apply  to  the  replacement  of  wearable  spare  parts  (see 
point 3).

8. 

The warranty is conditioned by using the genuine spare parts of the manufacturer.

Summary of Contents for SOFTER 9 PSW



















































Reviews: