- 25
-
Mi 2453/1
I
TALIANO
E
NGLISH
F
RANÇAIS
E
SP
AÑOL
P
OR
TUGUÊS
D
EUTSCH
Ringer tones volume
Ringing volume is the same for all the kind of calls.
-
To adjust it select “Ringer tones
vol.” and press
- an adjusting
bar is displayed on the screen - with
the buttons
or
adjust the
volume - press
- select “Save”
- press
.
Ringing Tones can be disabled choosing the lowest level
of volume in this menu or directly from the Device Man-
ager menu.
Ringing volume can be also momentarily adjusted acting
on the buttons
or
while receiving a call.
Display Backlight
Select Display Backlight - press
- chose the desired color from the list
or set a new color - press
- select
“Save” - press
.
Display contrast
Select LCD Contrast - press
-
an adjusting bar is displayed on the
screen, adjust the contrast of LCD
acting on the buttons
or
-
press
- select “save” - press
.
Advanced and System settings
Advanced and system settings are
fundamental
for the
correct working of the system, therefore they are acces-
sible only entering a 4-digit password. By factory default
the
passord is 1234
. It is advisable to change it with a per-
sonal one
(see chapter “Password”).
Attention
. It advisable to write down the new password
and keep it in a safe place; If you lose the password please
refer to FARFISA technical support.
Advanced
To access the advanced menu:
Press
- select “Settings” - press
- select “Ad-
vanced” - press
- enter the 4-digits password - press
- the following functions will be listed: Password,
Relay Mode, Relay Timing, Others, Restore Factory Settings,
Clear ALL bookings, Clear ALL alarms, Delete List, Recovery
Directory and Diagnostic.
Changing Password
To change the password it is necessary:
- select “Password” – press
- press
to erase the actual password –en-
ter the new 4-digits password - press
- select “Save” - press
.
New password in now stored.
Alarms
Mode
- Settings
Menu
Programming system
password
1234
####
21.09.11
11.06
Display backlight
- Advanced
Display contrast
Settings
Ringer tones volume
75%
- Red
Green
Blue
Display Backlight
Display contrast
50%
Operating mode of the internal relay.
Relay inside the switchboard (terminal boards C, NC, NO)
can be used for:
-
additional ringer
for the incoming calls, a lamp signaller
can also be driven
-
power-ON a CCTV monitor
only during the calls from the
door stations
-
bistable relay
operated by the button
; when the relay
is activated the LED
will light-Up
-
monostable relay
operated by the button
; when the
relay is activated the LED
will light-Up, timing of relay
should be set according the instructions of chapter
“Tim
-
ing of internal relay”.
- remain activated
when the doorkeeper excanger is
switched to
night mode.
To set the operating mode it is neces-
sary: - select “Relay Mode” - press
- select the requested mode - press
- select “Save” - press
.
Timing of internal relay
To set the activation time of relay, only
when the relay operates as
“Additional
ringer tone”
and
“Monostable”
, it is
necessary: - select “Relay Timing” –
press
- press
to erase the previous programmed
activation time – enter the new activation time in seconds
(from 1 to 99 sec.) - press
- select “Save” - press
.
Others
To operate these functions the assistance of a Farfisa
technician is necessary.
- Save DUO Logs
- LED x debug
- Video always ON
- Master flag ON
Factory settings
To restore the factory settings and reset all the data pre-
viously programmed (except the directory) it is necessary:
-select “Restore Factory Settings” -
press
- select
YES
to confirm or
NO
to exit - press
- select “Save”
- press
.
Clear all bookings
To cancel all the booking queue:
-select “Clear ALL bookings” – press
- select
YES
to confirm or
NO
to
exit - press
- select “Save” - press
.
Clear all alarms
To cancel all alarms:
-select “Clear ALL Alarms” – press
- select
YES
to confirm or
NO
to exit -
press
- select “Save” - press
.
- Addit.ringer tone
Monitor door sta
Bistable
Relay Mode
Programming relay time
activation
30
Restore Factory Set.
NO
YES
Clear ALL bookings
NO
YES
Clear ALL alarms
NO
YES