background image

1

IMPORTANT SAFEGUARDS

When using your Iron, basic safety precautions should always be
followed, including the following:

1. Read all instructions before using.
2. Use Iron only for its intended use. 
3. To protect against the risk of electric shock, do not immerse the

Iron in water or other liquids.

4. The Iron should always be turned to MIN before plugging or

unplugging from outlet. Never yank cord to disconnect from
outlet; instead, grasp plug and pull to disconnect.

5. Do not allow cord to touch hot surfaces. Let Iron cool completely

before putting away. Loop cord loosely around Iron when storing.

6. Always disconnect Iron from electrical outlet when filling with

water or emptying, and when not in use.

7. Do not operate with a damaged cord or plug, or if the Iron has

been dropped or damaged. To avoid the risk of electric shock, do
not disassemble the Iron; take it to a qualified service person for
examination and repair. Incorrect assembly can cause a risk of
electric shock when the Iron is used.

8. Close supervision is necessary for any appliance being used near

children. This appliance is not for use by children. Do not leave
hot Iron unattended while connected or on an ironing board.

9. Burns can occur from touching hot metal parts, hot water or

steam. Use caution when you turn a Steam Iron upside down.
There may be hot water in the Reservoir.

SPECIAL INSTRUCTIONS

1. This is a high wattage appliance. To avoid a circuit overload, do

not operate another high wattage appliance on the same circuit.

2. If an extension cord is absolutely necessary, a 15-ampere cord

should be used. Cords rated for less amperage may overheat. Care
should be taken to arrange the cord so that it cannot be pulled or
tripped over.

SAVE THESE INSTRUCTIONS

This product is for household use only

Summary of Contents for FSN100













Reviews: