Fanvil BW210 User Manual Download Page 37 | Manualshive

Page: 37 / 53

background image

37

Input Volume

Specify Input (MIC) Volume grade.

；

Handfree Volume

Specify Handfree Volume grade

G729 Payload Length

Set G729 Payload Length

Handdown Time

Specify the least reflection time of Handdown, the default is
200ms.

Output Volume

Specify Output (receiver) Volume grade.

Ring Volume

Specify Ring Volume grade

G722 Timestamps

160/20ms or 320/20ms is available

G723 Bit Rate

5.3kb/s or 6.3kb/s is available

Default Ring Type

Set up the ring by default

Signal Standard

Select Signal Standard.

VAD

Select it or not to enable or disable VAD. If enable VAD, G729
Payload length could not be set over 20ms.

4.3.4.2. Call Service

In this web page, you can configure Hotline, Call Transfer, Call Waiting, 3 Ways Call, Black List, white list
Limit List and so on.

Call Service

Field name

explanation

Hotline

Specify Hotline number. If you set the number, you can not dial any other
numbers.

No Answer Time

Specify No Answer Time

P2P IP Prefix

Set Prefix in peer to peer IP call. For example: what you want to dial is
192.168.1.119, If you define P2P IP Prefix as 192.168.1., you dial only #119
to reach 192.168.1.119. Default is “.”. If there is no “.” Set, it means to
disable dialing IP.

MWI Number

Set the number to listen record in server.

Do Not Disturb

Select NO Disturb, the phone will reject any incoming call, the callers will be
reminded by busy, but any outgoing call from the phone will work well.

Enable Call Transfer

Enable Call Transfer by selecting it.

Enable Call Waiting

Enable Call Waiting by selecting it.

Enable Three Way

Call

Enable Three Way Call

«
...
35
36
37
38
39
...
»

Summary of Contents for BW210






















































Reviews:

No comments

Related manuals for BW210

Brand: Samsung Pages: 155

Brand: Micromax Pages: 22

Brand: Jacob Jensen Pages: 76

alcatel Pixi4-7 4G BELL

Brand: TCL Pages: 41

Sphere AAP553G-315

Brand: Bauhn Pages: 40

Brand: C.R. Laurence Pages: 2

Brand: FLY Pages: 48

Brand: Sony Ericsson Pages: 40

Brand: bq Pages: 88

Brand: HTC Pages: 4

Brand: Viking Pages: 2

Brand: WELLTECH Pages: 47

Brand: M&T S.A. Pages: 68

Brand: Samsung Pages: 182

Brand: Samsung Pages: 193

Brand: Samsung Pages: 2

Brand: Samsung Pages: 183

Brand: Samsung Pages: 112

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands