Fanvil BW210 Page 30 User Manual Download | Manualshive

Page: 30 / 53

background image

30

Forward Phone Number

Appoint your forward phone number.

Server Type

Select the special type of server which is encrypted, or has some
unique requirements or call flows.

DTMF Mode

Select DTMF sending mode, there are three modes:

z

DTMF_RELAY

z

DTMF_RFC2833

z

DTMF_SIP_INFO

Different VoIP Service providers may provide different modes.

RFC Protocol Edition

Select SIP protocol version to adapt for the SIP server which uses
the same version as you select. For example, if the server is
CISCO5300, you need to change to RFC2543, else phone may
not cancel call normally. System uses RFC3261 as default.

Transport Protocol

Set transport protocols, TCP or UDP;

RFC Privacy Edition

Set Anonymous call out safely; Support RFC3323and RFC3325;

Subscribe Expire Time

Set the interval of Subscribe.

Enable DNS SRV

Support DNS looking up with _sip.udp mode

Click to Talk

Set click to Talk ( need practical software support).

Signal Encode

Enable/Disable Signal Encrypt.

RTP Encode

Enable/Disable RTP Encrypt.

Enable Session Timer

Set Enable/Disable Session Timer, whether support RFC4028.It
will refresh the SIP sessions.

Answer With Single Codec Enable/Disable the function when call is incoming, phone replies

SIP message with just one codec which phone supports.

Auto TCP

Set to use automatically TCP protocol to guarantee usability of

transport as message is above 1300 byte

Enable Strict Proxy

Support the special SIP server-when phone recieves the
patckets sent from server， phone will use the source IP
address, not the address in via field.

Enable GRUU

Set to support GRUU

Enable Displayname
Quote

Set to make quotation mark to displayname as the phone sends

out signal, in order to be compatible with server.

4.3.3.2. IAX2 Config

«
...
28
29
30
31
32
...
»

Summary of Contents for BW210






















































Reviews:

No comments

Related manuals for BW210

Brand: Icemobile Pages: 59

Brand: T-Mobile Pages: 4

Brand: Panasonic Pages: 4

Brand: United Security Products Pages: 24

Brand: Samsung Pages: 265

SPH-A600 Series

Brand: Samsung Pages: 111

Brand: WM Systems Pages: 102

Brand: Olitech Pages: 12

RED ALERT 397-710CB

Brand: GAI-Tronics Pages: 24

Brand: Blackberry Pages: 28

Brand: iBall Pages: 80

Brand: Med-Pat Pages: 37

Brand: Majestic Pages: 41

Brand: Samsung Pages: 221

Brand: Zte Pages: 24

Brand: Zte Pages: 24

Brand: Zte Pages: 112

Brand: Zte Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands