Fanvil BW210 Page 23 User Manual Download | Manualshive

Page: 23 / 53

background image

23

In chart 1, there is a layer 2 switch without setting VLAN. Any broadcast frame will be transmitted to the
other ports except the send port. For example, a broadcast information is sent out from port 1 then
transmitted to port 2,3and 4.
In chart 2, red and blue indicate two different VLANs in the switch, and port 1 and port 2 belong to red
VLAN, port 3 and port 4 belong to blue VLAN. If a broadcast frame is sent out from port 1, switch will
transmit it to port 2, the other port in the red VLAN and not transmit it to port3 and port 4 in blue VLAN. By
this means, VLAN divide the broadcast domain via

restricting the range of broadcast frame transmition.

Note: chart 2 use red and blue to identify the different VLAN, but in practice, VLAN uses different VLAN
IDs to identify.

QoS Configuration

Field name

explanation

VLAN Enable

Before select it to enable VLAN, you need enable Bridge mode in
LAN config.

VLAN ID Check Enable

Enable VLAN ID check by selecting it. After enable VLAN ID
check, if VLAN ID of a data package is not the same with the
phone’s or a data package do not have VLAN ID, the data package
will be discarded.

Voice/Data VLAN

differentiated

After enable VLAN, system will set packets with different type of
VLAN ID. Undifferentiated means after using VLAN, both VoIP
packets and other data packets will use the voice VLAN ID; tag
differentiated means after using VLAN, VoIP(signal and voice)
packets will add voice VLAN ID, and other data packets will add

«
...
21
22
23
24
25
...
»

Summary of Contents for BW210






















































Reviews:

No comments

Related manuals for BW210

Brand: Samsung Pages: 265

Sphere AAP553G-315

Brand: Bauhn Pages: 40

Brand: Grandstream Networks Pages: 11

Brand: M4 Pages: 22

Brand: Ericsson Pages: 71

Brand: ICON Pages: 8

Brand: Micromax Pages: 64

Brand: Geemarc Pages: 52

Brand: Geemarc Pages: 47

Brand: Geemarc Pages: 72

Brand: Telecom Pages: 2

Brand: Zte Pages: 82

Brand: Nokia Pages: 201

Brand: Zte Pages: 65

Brand: Zte Pages: 84

Brand: Samsung Pages: 2

Brand: Samsung Pages: 7

Brand: Samsung Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands