background image

 

18

Spa Maintenance 

 
 

FILTER CARTRIDGE MAINTENANCE 

 

Fantasy hot tubs use a screw in filter cartridge that is easily removed.  When the filter cartridge is removed, make 
sure no objects fall into the filter cavity.  They can cause obstructions to the water movement. 
 
Every two weeks, the filter cartridge must be cleaned to remove the objects and particles that have lodged in the 
cartridge pleats.  Using household water pressure and a garden hose with a pressurized nozzle, push water from 
inside to outside of the pleats, forcing all the trapped particles out.  If the cartridge is far too dirty to be cleaned as 
described above, contact your Fantasy dealer for a replacement. 

NOTE:  Never run your hot tub without a filter cartridge!!!   

 

NOTE:  Filter cartridges must be replaced every six months.  Restrictions in Filter quality can cause 
your hot tub pump to burn out and will not be covered under warranty. 
 

FILTER CARTRIDGE REMOVAL AND CLEANING INSTRUCTIONS 

 

Turn the power to the spa off, and then follow directions below: 

¾

 

Push

 down slightly and turn filter basket counter clockwise to unlock, then pull the basket and 

weir out. 

¾

 

Carefully

 unscrew the filter cartridge and bring it out of the spa. 

¾

 

Rinse

 cartridge using a garden hose. Rotate and separate filter pleats while spraying water to 

remove all dirt and debris possible. Let filter dry and look for calcium deposits (scaling) or an oil 
film. If you find these, you will need to deep clean your filter cartridge with a “spa filter cleaner” 
solution to break down and remove unwanted deposits and oils. (For longer filter life you should 
soak filter regularly.)   

   

      CAUTION!  Always use proper eye protection when using chemicals, or high 

pressure water.  Read instructions on cleaning products and follow applicable safety and 
warning instructions listed on label.
 

 

¾

 

Replace

 filter cartridge, then return basket and weir, insert and rotate clockwise to lock into 

position. Then, turn spa’s power back on. 

 

   

      CAUTION!  Never scrub the polyester mesh filter cartridge with a brush, as 

this will cause the polyester mesh to wear out and come apart.  Never let the spa pump 
run or have a filter cycle come on without a filter cartridge in the skimmer compartment.  
Running the spa without a filter cartridge may permit debris to enter the spa plumbing 
and void the warranty! 

 

SURFACE CARE 

 
Do not use solvents or abrasive cleaners to clean the hot tub.  Consult your Fantasy dealer for the proper cleaners.  
Typically, a mild detergent and water will resolve cleaning issues. 

   

     CAUTION!  Never spray cabinet with a garden hose for any reason since this 

action may induce an electrical short in the hot tubs electrical equipment. 

Summary of Contents for ILLUSION






















Reviews: