CARE & MAINTENANCE
The Fantasea
FRX100 VA R Housing
require
performance. The following tips will ena
1.
Always rinse your housing in streaming
water tub or rinse tank for about 20 minutes after every dive in order to dissolve the salt
water crystals from around the controls and openings of the housing.
movable controls to assist the removal of salt particles from these tight areas.
2.
Allow the housing to dry thoroughly before packing away for the day or for the trip home.
You may use a soft towel or cloth to dry the housing. Be sure there is no grease or other
debris on the towel.
3.
Visually check the condition of the
fresh water and dry it with a soft cloth as described
in any way, such as cut or perforated, replace it
4.
It is recommended to slightly lubricate the
that the amount of lubrication required on the O
place without friction, so it does not twist or become dislodged.
necessarily better, and in some
5.
Use only the supplied silicone grease for lubricating the
other grease might impair the watertight seal of the housing.
6.
Avoid removing the white O-ring featured on t
damaged.
7.
Be careful not to get greasy fingerprints or dirt on the lens port. This will affect the image
quality. Wipe any dirt or grease off with fresh water and a soft cloth.
8.
Never handle the housing with your ha
creams or petrol-related substances or liquids on the housing surface, as this can distort and
damage the housing materials.
9.
Do not drop the housing on hard surfaces
damaged.
10.
Do not disassemble or modify the housing, as this may cause leaks.
11.
Do not leave the housing in direct sunlight, inside a car in hot weather, or near a heater. Heat
may warp the housing and cause leaks. If you have to leave the h
important to cover it with a towel.
FRX100 VA R Housing Instruction Manual
35
CARE & MAINTENANCE
requires only a minimum amount of care for safe and
performance. The following tips will enable you to get the best results:
in streaming fresh water and if possible soak the housing in
nk for about 20 minutes after every dive in order to dissolve the salt
water crystals from around the controls and openings of the housing. Manipulate each of the
movable controls to assist the removal of salt particles from these tight areas.
using to dry thoroughly before packing away for the day or for the trip home.
You may use a soft towel or cloth to dry the housing. Be sure there is no grease or other
Visually check the condition of the black O-ring before every dive. If it is dirty, clean it with
fresh water and dry it with a soft cloth as described throughout the manual. If it is damaged
in any way, such as cut or perforated, replace it before using the housing again.
It is recommended to slightly lubricate the black O-ring periodically. It's important to note
the amount of lubrication required on the O-ring is only enough to allow it to slip into
place without friction, so it does not twist or become dislodged. More grease is not
in some cases might interfere with the housing watertight seal.
cone grease for lubricating the back door black O-ring. Use of any
other grease might impair the watertight seal of the housing.
ring featured on the back side of the front door unless it’s
Be careful not to get greasy fingerprints or dirt on the lens port. This will affect the image
quality. Wipe any dirt or grease off with fresh water and a soft cloth.
Never handle the housing with your hands coated in suntan, oil or cream. Avoid getting
related substances or liquids on the housing surface, as this can distort and
damage the housing materials.
Do not drop the housing on hard surfaces, it could crack and its watertight seal might be
Do not disassemble or modify the housing, as this may cause leaks.
Do not leave the housing in direct sunlight, inside a car in hot weather, or near a heater. Heat
p the housing and cause leaks. If you have to leave the housing in the sun, it is
important to cover it with a towel.
Instruction Manual 20200225
safe and reliable
housing in a fresh
nk for about 20 minutes after every dive in order to dissolve the salt
Manipulate each of the
movable controls to assist the removal of salt particles from these tight areas.
using to dry thoroughly before packing away for the day or for the trip home.
You may use a soft towel or cloth to dry the housing. Be sure there is no grease or other
If it is dirty, clean it with
If it is damaged
before using the housing again.
ring periodically. It's important to note
ring is only enough to allow it to slip into
More grease is not
cases might interfere with the housing watertight seal.
ring. Use of any
he back side of the front door unless it’s
Be careful not to get greasy fingerprints or dirt on the lens port. This will affect the image
nds coated in suntan, oil or cream. Avoid getting any oils,
related substances or liquids on the housing surface, as this can distort and
ight seal might be
Do not leave the housing in direct sunlight, inside a car in hot weather, or near a heater. Heat
ousing in the sun, it is
