Specifications — Falk LTG
The values shown are typical and slight variations are permissible.
AMBIENT TEMPERATURE RANGE — –20°F (–29°C) to 250°F
(121°C). Min. Pump = 20°F (–7°C).
MINIMUM BASE OIL VISCOSITY — 3300SSU (715cST) @
100°F (38°C).
THICKENER — Lithium & soap/polymer.
CENTRIFUGE SEPARATION CHARACTERISTICS — ASTM
#D4425 (Centrifuge Test) — K36 = 2/24 max., very high
resistance to centrifuging.
NLGI GRADE (ASTM D-217) —
1
/
2
CONSISTENCY (ASTM D-217) — 60 stroke worked penetration
value in the range of 315 to 360 measured at 77°F (25°C)
MINIMUM DROPPING POINT — 350°F (177°C) minimum
MINIMUM TIMKEN O.K. LOAD — 40 lbs.
ADDITIVES — Rust and oxidation inhibitors that do not corrode
steel or swell or deteriorate synthetic seals.
Packaging
14 oz. (0,4 kg ) CARTRIDGES — Individual or case lots of 10
or 60.
35 lb. (16 kg )PAIL, 120 lb. (54 kg ) KEG & 400 lb. (181 kg)
DRUMS.
General Purpose Grease
Annual Lubrication — The following specifications and
lubricants for general purpose grease apply to Falk Steelflex
couplings that are lubricated annually and operate within
ambient temperatures of 0°F to 150°F (–18°C to 66°C). For
temperatures beyond this range
(see Table 1),
consult
the Factory.
If a coupling leaks grease, is exposed to extreme temperatures,
excessive moisture or experiences frequent reversals, more
frequent lubrication may be required.
Specifications — General Purpose Coupling
Lubricants
The values shown are typical and slight variations are
permissible.
DROPPING POINT — 300°F (149°C) or higher.
CONSISTENCY — NLGI No. 2 with 60 stroke worked
penetration value in the range of 250 to 300.
SEPARATION AND RESISTANCE — Low oil separation rate and
high resistance to separation from centrifuging.
LIQUID CONSTITUENT — Possess good lubricating properties
... equivalent to a high quality, well refined petroleum oil.
INACTIVE — Must not corrode steel or cause swelling or
deterioration of synthetic seals.
CLEAN — Free from foreign inclusions.
General Purpose Greases Meeting Falk
Specifications
Lubricants listed below are typical products only and should not
be construed as exclusive recommendations
.
INSTALLATION OF TYPE T10 STEELFLEX
TAPERED GRID COUPLINGS
Installation
Only standard mechanics tools, wrenches, a straight edge and
feeler gauges are required to install Falk Steelflex couplings.
Clean all parts using a non-flammable solvent. Check hubs,
shafts and keyways for burrs.
INTERFERENCE FIT HUBS — Furnished without setscrews. Heat
hubs to a maximum of 275°F (135°C) using an oven, torch,
induction heater or an oil bath. To prevent damage DO NOT
heat hubs beyond a maximum temperature of 400°F (205°C).
When an oxy-acetylene or blow torch is used, use an excess
acetylene mixture. Mark hubs near the center of their length in
several places on hub body with a temperature sensitive
crayon, 275°F (135°C) melt temperature. Direct flame towards
hub bore using constant motion to avoid overheating an area.
WARNING:
If an oil bath is used, the oil must have a flash
point of 350°F (177°C) or higher. Do not rest hubs on the
bottom of the container. Do not use an open flame in a
combustible atmosphere or near combustible materials.
Heat hubs as instructed above. Mount hubs as quickly as possible
with hub flange face flush with shaft end. Allow hubs to cool
before proceeding. Insert setscrews (if required) and tighten.
®
The Falk Corporation, P.O. Box 492, Zip 53201-0492
428-112
3001 W. Canal St., Zip 53208-4200, Milwaukee, WI USA Telephone: 414-342-3131
May 2000
Fax: 414-937-4359 e-mail: [email protected] web: www.falkcorp.com
Supersedes 12-98
Installation and Maintenance
•
Steelflex
®
Couplings
(Page 2 of 6)
Sizes 1150–1260 & 150–260
•
Types T10
TABLE 1 — General Purpose Greases
H
Ambient Temperature Range
0°F to 150°F
(-18°C to 66°C)
-30°F to 100°F
(-34°C to 38°C)
Manufacturer
Lubricant
†
Lubricant
†
Amoco Oil Co.
Amolith Grease #2
Amolith Grease #2
BP Oil Co.
Energrease LS-EP2
Energrease LS-EP1
Chevron U.S.A. Inc.
Dura-Lith EP2
Dura-Lith EP1
Citgo Petroleum Corp.
Premium Lithium Grease EP2 Premium Lithium Grease EP1
Conoco Inc.
EP Conolith Grease #2
EP Conolith Grease #2
Exxon Company, USA
Unirex N2
Unirex N2
E.F. Houghton & Co.
Cosmolube 2
Cosmolube 1
Imperial Oil Ltd.
Unirex N2L
Unirex N2L
Kendall Refining Co.
Lithium Grease L421
Lithium Grease L421
Keystone Div. (Pennwalt)
81 EP-2
81 EP-1
Lyondell Petrochemical (ARCO) Litholine H EP 2 Grease
Litholine H EP 2 Grease
Mobil Oil Corp.
Mobilux EP111
Mobilith AW1
Petro-Canada Products
Multipurpose EP2
Multipurpose EP1
Phillips 66 Co.
Philube Blue EP
Philube Blue EP
Shell Oil Co.
Alvania Grease 2
Alvania Grease 2
Shell Canada Ltd.
Alvania Grease 2
Alvania Grease 2
Sun Oil Co.
Ultra Prestige 2EP
Ultra Prestige 2EP
Texaco Lubricants
Starplex HD2
Multifak EP2
Unocal 76 (East & West)
Unoba EP2
Unoba EP2
Valvoline Oil Co.
Multilube Lithium EP Grease . . .
H
Grease application or re-lubrication should be done at temperatures above
20°F (–7°C). If grease must be applied below 20°F (–7°C), consult The Falk
Corporation.
†
Lubricants listed may not be suitable for use in the food processing industry;
check with lube manufacturer for approved lubricants.
(.pdf revision)
