FOLD HERE &
PLACE ON HIGH
TEMPLATE FOR
INSTALLING
T–SERIES LEVER
LOCKS
MARK CENTERLINE OF LA TCH
FOR CORRECT DOOR
THICKNESS.
HIGH EDGE
LATCH
MARK CENTER FOR
5/16"(8mm) HOLES
USING DRILL
FIXTURE
030736-000-50 IS
RECOM-
MENDED TO
ENSURE
PROPER
ALIGNMENT
2 3/4"(70mm) BACKSET
MARK CENTER FOR
2 1/8"(54mm) HOLE
IMPORTANT
:
CHECK LOCK FOR PROPER
BACKSET BEFORE DRILLING
1 3/4"
(45mm)
2"(51mm)
2 1/4"(57mm)
5/32"(4mm)
5/32"(4mm)
x1/8"(3mm) DEEP
2"(51mm) DR
2
1
/
4
"(57mm) DR
1
3
/
4
"(45mm) DR
DOOR CENTERING ADJUSTMENT
STEP 9
ADJUST LOCK FOR DOOR THICKNESS
The lock is factory packed preadjusted for 1
³⁄₄
" (45 mm) doors unless
special ordered.
A. Place
the template provided against the retractor housing to find
the mark for door thickness.
B.
If adjustment is necessary, use hex wrench provided
and rotate flanged nut counterclockwise to adjust.
Again, use the template markings to measure adjustment
before installing lock on door.
Hint: Three full turns of the nut equals (=)
¹⁄₈
" (3 mm) adjustment.
C.
Pinch the button mount legs together and
move the cap to the desired position.
STEP 10
INSTALLING SPACER FOR DOORS THINNER
THAN 1
³⁄₄
" (45 mm)
A. Remove
the
flanged nut with the black hex wrench
provided, and remove the outer mounting plate.
B.
Place the spacer on over the outer chassis spindle
as shown.
C.
Re-install the outer mounting plate and flanged nut.
Using the adjusting gage provided, adjust the flanged nut
for proper door thickness as shown.
D.
Go back to Step 3 for chassis installation.
E.
Place the second spacer over the inner chassis
spindle before installing the inner mounting plate
and flanged nut. Continue at Step 5.
STEP 11
TO REMOVE ALL LEVERS WITH INTERCHANGEABLE CORE CYLINDERS
A.
Insert the control key into the core and rotate 15 degrees clockwise.
Pull the key to remove the core.
B.
Insert a screwdriver into the “figure 8” core hole and into the
lever retainer.
C.
Depress the retainer and slide the lever off the spindle.
TO RE-INSTALL THE LEVER
D.
Slide the lever over the spindle and push on over the retainer.
E.
Pull on the lever to be sure the retainer is engaged with the lever.
F.
Re-install the core with the tailpiece pushed into the core.
Chassis Assembly
Button Mount Legs
Cap
2
¹⁄₄
"
(57 mm)
2"
(51 mm)
1
³⁄₄
"
(45 mm)
Flanged Nut
Black Hex Wrench
Inner Mounting Plate
Flanged Nut
Gage
Spacer
Outer Mounting Plate
Spacer
Chassis Assembly
Flanged Nut
Spacer
Outer Mounting Plate
Push
Retainer
Control Key
DOOR CENTERING
ADJUSTMENT GAGE
NT FALCON T-SERIES LEVER
LOCKS FOR DOORS LESS THAN
1 3/4 (45mm) THICK
NT FALCON LOCK
P/N 030793-001-70
PRINTED IN U.S.A.
Outs
ide
Inside
1 3/4 (45mm)
1 1/4 (32mm)
1 1/2 (38mm)
A
B
