background image

Pic. 7

Aproli 280 Batt

installed on the 

left

Aproli 280 Batt

installed on the 

right

E

n

g

li

sh

7

SETTING TO GATE OPERATION - APROLI 280 BATT INSTALLED ON TO THE RIGHT AND LEFT

Once satisfied that voltage is properly supplied to the motors, operator setting is to be attended. Aproli 280 Batt installed on the 
left is factory pre-set, gate in closed position. Whereas with Aproli 280 Batt installed on the right, it is required that the motor shaft 
be turned to the end of the permitted rotation.
As next step with both operators, the motor shafts are to be rotated a few degrees in the open direction allowing for the arms to 
be fixed.

FIXING THE BACK BRACKET TO THE GATE POST 

The back bracket is to be fixed to the gate post by means of suitable expanding bolts using 4 of the 8 holes provided in it.

M8 expanding bolts

to suit gate post

material or 

brickwork

Pic. 8

250 

150 

212 

120 

355 

400 

Gate view from inside

External oil-hydraulic operator with articulated arm 

for swinging gates mounted on large pillars

APROLI 280 Batt

Pic. 9

Power supply

terminals 

Should the shaft turn in the wrong direction, 

swap power supply to the other phase terminal 

230 V - 50 Hz

blue

 c

ommon

phase

230 V - 50 Hz

blue

 c

ommon

phase

Summary of Contents for APROLI 280 BATT













Reviews: