background image

IV

CONTENTS

1 Safety ...................................................................1

1.1 Instructions for safe operations................ 1
1.2 Warning ..................................................... 1
1.3 Attention.................................................... 2

2 Overview.............................................................4

2.1 Features...................................................... 5
2.2 Major applications and scope of
application........................................................... 5
2.3 Environment requirements....................... 5

3 Principle..............................................................6

4 Technical specifications ....................................7

4.1 Main performance..................................... 7
4.2 Main Parameters ....................................... 7

5 Installation..........................................................8

5.1 View of the front panel............................. 8
5.2 Battery installation.................................... 8
5.3 Accessories................................................ 9

6 Operating Guide................................................9

6.1 Application method................................... 9
6.2

Attention for operation ......................... 14

6.3 Clinical restrictions................................. 15

7 Maintain

transportation and storage........16

7.1 Cleaning and Disinfecting...................... 16
7.2 Maintain................................................... 16
7.3 Transportation and storage ..................... 17

8 Troubleshooting ...............................................17
9 Key of Symbols ................................................19

10 Function Specification .....................................21

1

1 Safety

1.1 Instructions for safe operations

Check the main unit and all accessories

periodically to make sure that there is no visible
damage that may affect patient

s safety and

monitoring

performance

about

cables

and

transducers. It is recommended that the device
should be inspected once a week at least. When there
is obvious damage, stop using the device.

Necessary maintenance must be performed by

qualified service engineers ONLY. Users are not
permitted to maintain it by themselves.

The oximeter cannot be used together with

devices not specified in User

s Manual.Only the

accessory that appointed or recommendatory by
manufacture can be used with this device.

This product is calibrated before leaving factory.

1.2 Warning

Explosive hazard

DO NOT use the oximeter in

environment with inflammable gas such as some
ignitable anesthetic agents.

DO NOT use the oximeter while the testee

measured by MRI and CT.

The person who is allergic to rubber can not use

this device.

Summary of Contents for CMS-50D Plus


















Reviews: