12
ENGLISH
To use radiocontrols with the same code, copy the
ON - OFF combination to the other radiocontrols
without the need to change anything on the control
board.
6.2 STORING SLH RADIOCONTROLS
It is possible to store a maximum of
256 codes divided between OPEN A and
OPEN B/CLOSE.
On the SLH radiocontrol, press and hold down P1 and
P2 simultaneously.
The radiocontrol led will begin to flash.
Release both push-buttons.
Press and hold down push-button
+
(SW3) or
-
(SW2)
and then press the SETUP push-button (SW4), to store
total opening (OPEN A) or partial opening (OPEN B/
CLOSE) respectively. The corresponding led will begin
to flash slowly for 5 secs.
Release both push-buttons.
Within this 5 sec. period while the radiocontrol led is still
flashing, press and hold down the required push-button
on the radiocontrol (the radiocontrol led will come on
with a fixed light).
The corresponding led will come on with a fixed light
for 2 seconds and then go off to indicate the setting
has been stored.
Release the radiocontrol push-button.
Press the stored radiocontrol push-button twice in quick
succession.
The automated system will carry out an
opening control. Ensure the automated
device is free of any obstacle by people
or things.
To enable other radiocontrols with the same system code,
transfer the system code of the stored radiocontrol push-
button to the corresponding push-button of the radiocon-
trols to be added, following the procedure below:
On the stored radiocontrol, press and hold down
P1 and P2 simultaneously.
The radiocontrol led will begin to flash.
Release both push-buttons.
Press the stored push-button and hold down (the
radiocontrol led will come on with a fixed light).
Bring the radiocontrols closer to one another, press
and hold down the corresponding push-button of
the radiocontrol to be added, releasing only once
the led on the radiocontrol has issued a double
flash to indicate that it has been stored.
Press the stored radiocontrol push-button twice in
quick succession.
The automated system will carry out an
opening control. Ensure the automated
device is free of any obstacle by people
or things.
7.
1.
2.
3.
4.
5.
6.
7.
8.
9.
a.
b.
c.
d.
e.
f.
6.3 STORING LC/RC RADIOCONTROLS
(ONLY FOR SOME MARKETS)
It is possible to store a maximum of
256 codes divided between OPEN A and
OPEN B/CLOSE.
Use the LC/RC remote controls only with a
433 MHz receiving module.
Press and hold down push-button
+
(SW3) or
-
(SW2)
and then press the SETUP push-button (SW4), to store
total opening (OPEN A) or partial opening (OPEN B/
CLOSE) respectively. The corresponding led will begin
to flash slowly for 5 secs.
Release the push-button.
Within this 5 second period, press the required push-
button on the LC/RC remote control.
The led will come on with a fixed light for 1 second,
indicating that the unit has been stored, and then
resume flashing for an additional 5 seconds during
which time another radiocontrol may be stored.
Once the 5 seconds are up, the led will go off to indi-
cate that the procedure is complete.
6.3.1 STORING LC/RC RADIOCONTROLS REMOTELY
With LC/RC radiocontrols, other radiocontrols may be
stored in remote mode, i.e. without operating directly on
the board, using a previously stored radiocontrol.
Obtain a radiocontrol already stored on one of its
2 channels (OPEN A or OPEN B/CLOSE).
Press and hold down push-buttons P1 and P2 simulta-
neously until both leds flash slowly for 5 secs.
Within 5 seconds, push the previously stored radiocon-
trol push-button to activate the learning stage on the
selected channel.
The led on the board corresponding to the channel
being stored flashes for 5 seconds, within which time
the code of another radiocontrol must be sent.
The led will come on with a fixed light for 1 second,
indicating that the unit has been stored, and then
resume flashing for an additional 5 seconds during
which time other radiocontrols may be stored and
then it will go off.
6.4 RADIOCONTROLS DELETION PROCEDURE
To delete
ALL
the codes of the radiocontrols entered,
simply press down together the two push-buttons
+
(SW3)
and
-
(SW2), then press the SETUP push-button (SW4) for
1 second, and hold the first two push-buttons pressed for
10 secs.
The 2 leds RADIO1 and RADIO2 will flash quickly for
10 secs.
The 2 leds will come on with a fixed light for 2 seconds
and then go off (deletion carried out).
Release both push-buttons.
This operation is NOT reversible. All the codes
of the radiocontrols stored as OPEN A and
as OPEN B/CLOSE will be deleted.
1.
2.
3.
4.
5.
1.
2.
3.
4.
5.
•
•
•
