background image

E045S 

532373 - Rev.A

1-E045S

dd/mm/yy

Tr

ansla

tion of the orig

inal instruc

tions

ENGLISH

3.1  INTENDED USE

The FAAC E045S electronic board has been designed 

to control actuators (hydraulic or electromechanical) 

intended for installation in areas that are accessible to 

people, the main purpose of which is to provide safe 

access for goods or vehicles or people in industrial, 

commercial or residential settings.

 

!

Any  other  use  that  is  not  expressly  specified  in 

these instructions is prohibited and could affect the 

integrity of the product and/or represent a source 

of danger.

3.2  LIMITATIONS OF USE

 

-

The E045S can control one or two 230 V

~

 actuators. 

 

-

The product may not be used in a constructional 

configuration other than the one provided for by 

FAAC S.p.A. 

 

-

No component part of the product may be modi-

fied.

3.3  UNAUTHORISED USE

 

-

Do not use on motors or devices that are intended 

for purposes other than operating gates.

 

-

Uses other than the intended use are prohibited.

 

-

It is prohibited to install the E045S on smoke and/

or fire doors.

 

-

It is prohibited to install the E045S in environments 

in which there is a risk of explosion and/or fire: the 

presence of flammable gases or fumes is a serious 

safety hazard (the product is not ATEX certified).

 

-

It is prohibited to power the system with energy 

sources other than those specified.

 

-

It is prohibited to integrate commercial systems 

and/or equipment other than those specified, or 

use them for purposes not envisaged and author-

ised by the corresponding manufacturers.

 

-

It is prohibited to use and/or install accessories 

which have not been specifically authorised by 

FAAC S.p.A.

 

-

It is prohibited to use the E045S in the presence of 

faults which could compromise safety.

 

-

Do not allow water jets of any type or size to come 

into direct contact with the E045S.

 

-

Do not expose the E045S to corrosive chemical or 

environmental agents.

3.4  PRODUCT IDENTIFICATION

day/month/year

of construction

identification code

model

3.  E045S

Summary of Contents for E045S

































Reviews: