a
Fig. 10
Fig. 11
10 MM
16 MM
+
16 MM
10
AUTOMATED SYSTEM TEST
When you have finished programming, check if the system is
operating correctly. In particular, check if the safety devices
are operating correctly.
8.3.1 REMOTE MEMORY STORAGE OF RC RADIO
CONTROLS
Other radio controls can be remotely stored only with the RC
radio controls, i.e. without using the LOGIC-SPEED-SETUP push-
buttons, but using a previously stored radio control.
Get a radio control already stored on one of the 2 channels
(OPEN A or OPEN B).
Press and hold down push-buttons P1 and P2 simultaneously
until both the LEDs flash slowly for 5 sec.
Within 5 sec. press the push-button of the radio control
that had been memory stored to enable learning on the
selected channel.
1.
2.
3.
Quickly press twice the memory stored radio control push-
button.
The automated system performs one opening
operation. Make sure that the automated
system is free of any obstacle created by
persons or things.
To add other radio controls, transfer the code of the memory-
stored push-button of the radio control to the relevant push-
button of the radio controls to be added, observing the
following procedure.
On the memory stored radio control, simultaneously press
and hold down push-buttons P1 and P2.
The radio control LED begins to flash.
Release both push-buttons.
Press the memory stored push-button and hold it down
(the radio control LED lights up on steady beam).
Bring the radio controls near, press and hold down the
push-button of the radio control to be added, releasing
it only after the double flash of the radio control LED,
which indicates memory storage executed.
Quickly press twice the push-button of the memory stored
radio control.
The automated system performs one opening
operation. Make sure that the automated
system is free of any obstacle created by
persons or things.
8.3 MEMORY STORAGE OF RC RADIO CONTROLS
A maximum of 250 codes can be memory
stored, split between OPEN A and OPEN B.
Use RC remote controls only with receiver module at 433
MHz.
Press the LOGIC (SW3) or SPEED (SW2) push-button, to
memory store respectively total opening (OPEN A) or partial
opening (OPEN B), and as you hold it down, also press the
SETUP (SW1) push-button. The relevant LED starts to flash
slowly for 5 sec.
Release both push-buttons. Within these 5 sec., press the
appropriate push-button on the RC remote control.
The LED lights up on steady beam for 1 second, indicating
memory storage executed, and then resumes flashing for
another 5 sec., during which another radio control (point
4) can be memory stored.
When the 5 sec. have elapsed, the LED goes OFF indicating
the end of the procedure.
To add other radio controls, repeat the operation at point 1.
9.
•
•
•
•
•
•
1.
2.
3.
4.
5.
6.
The LED on the board relating to the channel being learned
flashes for 5 sec., within which time the code of another
radio control must be transmitted.
The LED lights up on steady beam for 2 seconds, indicating
memory storage executed, and then resumes flashing for
5 sec., during which other radio controls can be memory
stored, and then goes OFF.
8.4
RADIO CONTROLS DELETION PROCEDURE
To delete
ALL
the input radio control codes, press push-
button LOGIC (SW3) or SPEED (SW2) and, while holding it
down, also press push-button SETUP (SW1) for 10 sec.
The LED relating to the pressed push-button flashes for
the first 5 sec, and then flashes more quickly for the next
5 sec.
Both LEDs light up on steady beam for 2 sec and then go
OFF (deletion completed).
Release both push-buttons.
This operation is NOT reversible. All codes of
radio controls stored as OPEN A and OPEN B will
be deleted.
4.
5.
1.
2.
3.
4.
9
BATTERY KIT (OPZIONAL)
The buffer battery kit was built for insertion inside the control
board support.
This support (Fig.10 ref.
a
) was pre-moulded to permit the
battery housing to be opened.
Remove the board support material covering the
battery housing, cutting the material connections along
the perimeter.
1.
Insert the battery in the housing you have just created, and
secure it on the anchoring supports (Fig.11).
2.
To correctly fasten and connect the kit to the control
unit, consult the instructions enclosed with the
battery kit.
3.
ENGLISH
9
Summary of Contents for E024S
Page 1: ...E024S...
