background image

C850 

33 

532015 - Rev.B

T

ranslation of the original instructions

ENGLISH

12.4  INVERTER ERROR

Alarm Code

Alarm Name

Alarm Description

E 05

Stop due to overload

Excessive motor strain

Troubleshooting: 

1.  Sliding leaf too heavy.
2.  Obstacle preventing correct movement of the sliding leaf.

Alarm Code

Alarm Name

Alarm Description

E 07

Stop due to overvoltage

• 

Input power voltage too high or deceleration too fast.

• 

The currents generated could damage the inverter.

Troubleshooting: 

1.  Ensure that the power voltage of terminals L and N is correct.

2.  Press STOP/RESET on the inverter.

3.  Check the RUNNING SPEED, inverter parameter A021, and reduce the speed, if necessary.
4.  Check the MINIMUM STOP SPACE in chart 1 in section 6.2 FINAL ADJUSTMENT OF THE LIMIT SWITCHES, and, if necessary, 

increase the stop space by adjusting the limit switches.

5.  Check the DECELERATION SPACE, as shown in section 6.2 FINAL ADJUSTMENT OF THE LIMIT SWITCHES, and, if necessary, 

increase the deceleration space by adjusting the limit switches.

6.  Check the DECELERATION set in the parameter F003, as shown in section 6.2 FINAL ADJUSTMENT OF THE LIMIT SWITCHES, 

paragraphs 13 and 14, and, if necessary, increase the deceleration value.

NOTE: In case of other ERROR warnings, wait  (10 sec) for the inverter to reset automatically.

 If the ERROR persists, press STOP/RESET

Summary of Contents for C850









































Reviews: