ENGLISH
ENGLISH
5
1) CAUTION! It is important for personal safety to follow all the instructions
carefully. Incorrect installation or misuse of the product may cause
people serious harm.
2) Read the instructions carefully before starting to install the product.
3) Packaging material (plastic, polystyrene, etc.) must not be left within
reach of children as it is a potential source of danger.
4) Keep the instructions in a safe place for future reference.
5) This product was designed and manufactured strictly for the use
indicated in this documentation. Any other not expressly indicated use
may damage the product and/or be a source of danger.
6) FAAC accepts no responsibility due to improper use of the automation
or use other than that intended.
7) Do not install the appliance in an area subject to explosion hazard:
inflammable gasses or fumes are a serious safety hazard.
8) Mechanical construction elements must meet the provisions of UNI8612,
CEN pr EN 12604 and CEN pr EN 12605 Standards.
To obtain an adequate level of safety in non EU countries, the above
mentioned Standards must be observed in addition to national
standards.
9) FAAC will not accept responsibility if the principles of Good Workman-
ship are disregarded in constructing the closing elements to be motor-
ised, and if any deformation occurs during use of the said elements.
10) Installation must meet the following Standards: UNI8612, CEN pr EN
12453 and CEN pr EN 12635.
The safety class for the automation must be C+D.
11) Before carrying out any work on the system, switch off the power
supply.
12) The mains power supply of the automation must be fitted with a all-
pole switch with contact opening distance of 3mm or greater. Use of
a 6A thermal breaker with all-pole circuit break is recommended.
13) Make sure there is a differential switch with 0.03A threshold upstream
of the system.
CE DECLARATION OF CONFORMITY
Manufacturer:
FAAC S.p.A.
Address:
Via Benini, 1 - 40069 Zola Predosa BOLOGNA - ITALY
Declares that:
Electronic appliance 424MPS
• conforms to the essential safety requirements of the following directives:
73/23/EEC and subsequent amendment 93/68/EEC.
89/336/EEC and subsequent amendment 92/31/CEE and 93/68/EEC
Additional information:
This product underwent tests in a typical, uniform configuration (all products manufactured by FAAC S.p.A.).
Bologna 01 January 2000
The Managing Director
A. Bassi
14) Check that the earthing system is correctly made and connect the
closure metal parts to it. Also connect the Yellow/Green wire of the
automation to the earthing system.
15) The automation includes an intrinsic anti-crushing device consisting
of a torque control which, however, must be installed together with
other safety devices.
16) The safety devices [e.g.: photocells, sensitive edges, etc…] protect
any dangerous areas against
Movement mechanical risks
, such as,
crushing, dragging, or shearing.
17) Use of at least one indicator-light is essential for each system (e.g.:
FAAC LAMP MINILAMP, etc.) as well as a sign adequately fixed to the
frame structure, in addition to the devices mentioned at point “16”.
18) FAAC accepts no responsibility regarding safety and correct opera-
tion of the automation, should components made by manufacturers
other than FAAC be used in the system.
19) Use only FAAC original spare parts for maintenance.
20) Do not make any alterations to the components of the automation.
21) The installer must supply full information regarding manual operation
of the system in case of an emergency and hand to the user of the
system the “User’s Guide” included with the product.
22) Do not allow children or other persons to stand near the product while
in operation.
23) Keep remote controls or any other pulse generator well away from
children, to prevent the automation from being activated acciden-
tally.
24) The user must refrain from attempting to repair or adjust the system
personally and should contact qualified personnel only.
25) Anything not expressly provided for in these instructions is not permit-
ted.
WARNING FOR THE INSTALLER
GENERAL SAFETY OBLIGATIONS
