background image

To the original purchaser only:

 FAAC International, 

Inc., warrants, for twenty-four (24) months from the 
date of invoice, the gate operator systems and other 

related systems and equipment manufactured by FAAC 
S.p.A. and distributed by FAAC International, Inc., to be 
free from defects in material and workmanship under 

normal use and service for which it was intended 

provided

 it has been properly installed and operated. 

FAAC International, Inc.'s obligations under this 

warranty shall be limited to the repair or exchange of 
any part of parts manufactured by FAAC S.p.A. and 
distributed by FAAC International, Inc. Defective 

products must be returned to FAAC International, Inc., 
freight prepaid by purchaser, within the warranty 
period. Items returned will be repaired or replaced, at 

FAAC International, Inc.'s option, upon an examination 
of the product by FAAC International, Inc., which 
discloses, to the satisfaction of FAAC International, Inc., 

that the item is defective. FAAC International, Inc. will 
return the warranted item freight prepaid. The products 
manufactured by FAAC S.p.A. and distributed by FAAC 

International, Inc., are not warranted to meet the 
specific requirements, if any, of safety codes of any 
particular state, municipality, or other jurisdiction, and 

neither FAAC S.p.A. or FAAC International, Inc., assume 
any risk or liability whatsoever resulting from the use 
thereof, whether used singly or in combination with 

other machines or apparatus. 

Any products and parts not manufactured by FAAC 

S.p.A. and distributed by FAAC International, Inc., will 

carry only the warranty, if any, of the manufacturer. This 
warranty shall not apply to any products or parts thereof 
which have been repaired or altered, without FAAC 

International, Inc.'s written consent, outside of FAAC 
International, Inc.'s workshop, or altered in any way so 
as, in the judgment of FAAC International, Inc., to affect 

adversely the stability or reliability of the product(s) or 
has been subject to misuse, negligence, or accident, or 
has not been operated in accordance with FAAC 

International, Inc.'s or FAAC S.p.A.'s instructions or has 

been operated under conditions more severe than, or 

otherwise exceeding, those set forth in the 
specifications for such product(s). Neither FAAC S.p.A. 

or FAAC International, Inc., shall be liable for any loss or 
damage whatsoever resulting, directly or indirectly, 
from the use or loss of use of the product(s). Without 

limiting the foregoing, this exclusion from liability 
embraces a purchaser's expenses for downtime or for 
making up downtime, damages for which the purchaser 

may be liable to other persons, damages to property, 
and injury to or death of any persons. Neither FAAC 
S.p.A. or FAAC International, Inc., assumes nor 

authorizes any person to assume for them any other 
liability in connection with the sale or use of the 
products of FAAC S.p.A. or FAAC International, Inc. The 

warranty hereinabove set forth shall not be deemed to 
cover maintenance parts, including, but not limited to, 
hydraulic oil, filters, or the like. No agreement to replace 

or repair shall constitute an admission by FAAC S.p.A. or 
FAAC International, Inc., of any legal responsibility to 
effect such replacement, to make such repair, or 

otherwise. This limited warranty extends only to 
wholesale customers who buy directly through FAAC 
International, Inc.'s normal distribution channels. FAAC 

International, Inc., does not warrant its products to end 
consumers. Consumers must inquire from their selling 
dealer as to the nature and extent of that dealer's 

warranty, if any. 

This warranty is expressly in lieu of all other 

warranties expressed or implied including the war-
ranties of merchantability and fitness for use. This 
warranty shall not apply to products or any part 

thereof which have been subject to accident, negli-
gence, alteration, abuse, or misuse or if damage was 
due to improper installation or use of improper 

power source, or if damage was caused by fire, flood, 
lightning, electrical power surge, explosion, wind 
storm, hail, aircraft or vehicles, vandalism, riot or 
civil commotion, or acts of God. 

L

IMITED

 W

ARRANTY

 

FAAC International, Inc.

 

303 Lexington Avenue 

Cheyenne, WY  82007 

www.faacusa.com 

Page 28 

January,  200 4 
412 O pe rator And  
455 D  Control Panel I nst allatio n M anual   

Summary of Contents for 412 Compact





























Reviews: