background image

 
 
 

 

 

 

 

Your tool requires lubrication before using it for the first time. 

 
 

 

Disconnect the air supply from the tool before lubricating. 

 
 

Turn the tool so the inlet is facing up and put one drop of pneumatic oil 

into  the  air  inlet.  Never  use  detergent  oil  additives.  Operate  the  tool 

briefly after adding oil. 

                                                                         

 

                                                                       

Wipe off excessive oil at the exhaust. Excessive oil will damage 

                                                                                O-rings of tool.  
 
 

 

 
 

 

 

 

The following illustration shows the correct mode of connection to the air supply system, 

which will increase the efficiency and the lifetime of the tool. 

 

 
 

It  is  recommended  to  use  an  automatic  oiler  to  provide  oil  circulation 

and  increase  the  efficiency  and  lifetime  of the  tool.  Check  the  oil  level 

daily. 

 
 

Besides the oiler also the use of a filter is recommended. This removes 

liquid  impurities  which  can  cause  rust  or  wear  to  internal  parts  of  the 

tool.  A  filter  also  increases  the  efficiency  and  the  lifetime  of  the  tool. 

The filter must be checked on a daily basis and drained if necessary. 

 Lubrication and Maintenance 

NOTE 

 Air Supply and Connections 

NOTE 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

Summary of Contents for CL45A



























Reviews: