F.F. Group ID 550 PLUS, Original Instructions Manual

Page: 6 / 32

| English 6 ID 550 PLUS
ChANGING ThE TOOL
Wear protective gloves when changing the
tool. The drill chuck can become very hot
during longer work periods.
h
Open the key type drill chuck (07) by turning until
the tool can be inserted.
h
Insert the tool.
h
Insert the chuck key (09) into the corresponding
holes of the key type drill chuck (07) and clamp the
tool uniformly.
SCREWDRIVER TOOLS
When working with screwdriver bits, a universal bit
holder should always be used. Use only screwdriver
bits that fit the screw head. For driving screws, al -
ways position the “Drilling/Impact Drilling” selec -
tor switch (05) to the “Drilling” mode.
OPERATION
REVERSING ThE ROTATIONAL DIRECTION
The rotational direction switch (04) is used to
reverse the rotational direction of the machine.
However, this is not possible with the On/Off
switch (01) actuated.
ƒ
Right rotation: For drilling and screwing in
screws, push the rotational direction switch (04)
toward the left.
ƒ
Left rotation: For loosening and unscrewing
screws and nuts, push the rotational direction
switch (04) toward the right.
SETTING ThE OPERATING mODE
h
Drilling and Screwdriving: Set the selector switch
(05) to the “Drilling” symbol .
h
Impact Drilling: Set the selector switch (05) to the
“Impact drilling” symbol .
The selector switch engages noticeably and can
also be actuated with the machine running.
SwITChING ON AND OFF
h
To start the machine, press the On/Off switch (01)
and keep it pressed.
h
To lock the pressed On/Off switch (01) , press the
lock-on button (02) .
To switch off the machine, release the On/Off
switch (01) or when it is locked with the lock-on
button (02) , briefly press the On/Off switch (01)
and then release it.
ADjUSTING ThE SpEED/IMpACT RATE
The speed/impact rate of the switched on power
tool can be variably adjusted, depending on how
far the On/Off switch (01) is pressed.
Light pressure on the On/Off switch (01) results
in low speed/impact rate. Further pressure on the
switch increases the speed/impact rate.
pRESELECTING ThE SpEED/IMpACT RATE
With the thumbwheel for speed preselection (03) ,
the required speed/impact rate can be preselect -
ed even during operation. The required speed/im -
pact rate depends on the material and the work-
ing conditions, and can be determined through
practical testing.
mAINTENANCE
Regular inspection and cleaning reduces the neces-
sity for maintenance operations and will keep your
tool in good working condition. The motor must be
correctly ventilated during tool operation. For this
reason avoid blocking the air inlets.
ENVIRONmENTAL PROTECTION
Recycle raw materials instead of disposing as
waste. Machine, accessories and packaging
should be sorted for environment - friendly re -
cycling. The plastic components are labeled for
categorized recycling.
EXpLANATION OF SyMBOLS
Double insulation
For indoor use only. Do not expose to
rain.
Wear eye protection.
Damage to lungs if an effective dust mask
is not worn.
Wear protective gloves
Damage to hearing if effective hearing
protection is not worn.
To reduce the risk of injury, the user must
read and understand this manual before
using this product.
Important!
Conforms to relevant safety standards
GUARANTEE
This product is warranted in accordance with the
legal/country specific regulations, effective from
the date of purchase by the first user. Damage
attributable to normal wear and tear, overload or
improper handling will be excluded from the guar-
antee. In case of a claim, please send the machine,
completely assembled, to your dealer or the ser-
vice Centre for electric power tools.